Hayward Flow Control
Hayward Flow Control
Pipe Sizing Chart
MINIMUM INLET PIPING SIZE CHART
Pipe Size
in. [mm]
2 ½” [64]
3” [76]
4” [102]
6” [152]
* NOTE -
to 5 pipe size diameters, be used between the pump suction inlet and any plumbing fittings (elbows, valves, etc.).
Plumbing
Use PTFE
cleaned before use.
When applying
tape. Wind the tape clockwise as you face the open end of the fitting, beginning at the end of the fitting. It is only nece
to tighten fittings enough to prevent leakage. Tighten fitting by hand and then use a tool to engage fitting an add
turns. Use care when using
damage
. If leaks occur, remove connector, clean off old
and re-install connector.
Fittings restrict flow. For better efficiency, use the fewest possible fittings (but at least two suction outlets). Avoid f
that could cause an air trap.
main drain).
Electrical
that the electrical supply available agrees with the motor’s voltage, phase, and cycle, and that the wire size is adequate fo
amps rating and distance from the power s
Hayward Flow Control
Pipe Sizing Chart
MUM INLET PIPING SIZE CHART
Pipe Size
in. [mm]
2 ½” [64]
3” [76]
4” [102]
6” [152]
It is recommended that a minimum length of straight piping (s
to 5 pipe size diameters, be used between the pump suction inlet and any plumbing fittings (elbows, valves, etc.).
system op
components may fail resulting in severe personal injury or death.
Plumbing
tape
to seal threaded connections on molded plastic components. All plastic fitti
cleaned before use.
NOTE
applying PTFE tape
tape. Wind the tape clockwise as you face the open end of the fitting, beginning at the end of the fitting. It is only nece
to tighten fittings enough to prevent leakage. Tighten fitting by hand and then use a tool to engage fitting an add
turns. Use care when using
. If leaks occur, remove connector, clean off old
install connector.
Fittings restrict flow. For better efficiency, use the fewest possible fittings (but at least two suction outlets). Avoid f
that could cause an air trap.
main drain).
lectrical
regulations, and the National Electric Code (NEC).
ground and bond pump motor can cause serious or fatal electrical shock hazard.
gas supply line.
on electrical c
that the electrical supply available agrees with the motor’s voltage, phase, and cycle, and that the wire size is adequate fo
rating and distance from the power s
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
MUM INLET PIPING SIZE CHART
Minimum Suction Pipe
Length
“L”
12 ½” [317]
15” [381]
20” [508]
30” [762]
It is recommended that a minimum length of straight piping (s
to 5 pipe size diameters, be used between the pump suction inlet and any plumbing fittings (elbows, valves, etc.).
WARNING
system operate under pressure. Incorrectly installed and/or improperly tested equipment and/or
components may fail resulting in severe personal injury or death.
to seal threaded connections on molded plastic components. All plastic fitti
NOTE - Do NOT use Plumber’s Pipe Dope as it may cause cracking of the plastic components.
tape
to plastic threads, wrap the entire threaded portion of the male fitting with one to two l
tape. Wind the tape clockwise as you face the open end of the fitting, beginning at the end of the fitting. It is only nece
to tighten fittings enough to prevent leakage. Tighten fitting by hand and then use a tool to engage fitting an add
turns. Use care when using PTFE tape as friction is reduced considerably;
. If leaks occur, remove connector, clean off old
Fittings restrict flow. For better efficiency, use the fewest possible fittings (but at least two suction outlets). Avoid f
that could cause an air trap. Use a non-
WARNING
regulations, and the National Electric Code (NEC).
WARNING
ground and bond pump motor can cause serious or fatal electrical shock hazard.
gas supply line.
To avoid dangerous or fatal electrical shock, turn OFF power to motor before working
on electrical connections.
that the electrical supply available agrees with the motor’s voltage, phase, and cycle, and that the wire size is adequate fo
rating and distance from the power s
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
www.haywardflowcontrol.com
MUM INLET PIPING SIZE CHART
Minimum Suction Pipe
“L”
in. [mm] *
12 ½” [317]
15” [381]
20” [508]
30” [762]
It is recommended that a minimum length of straight piping (s
to 5 pipe size diameters, be used between the pump suction inlet and any plumbing fittings (elbows, valves, etc.).
WARNING
–
Hazardous Pressure.
erate under pressure. Incorrectly installed and/or improperly tested equipment and/or
components may fail resulting in severe personal injury or death.
to seal threaded connections on molded plastic components. All plastic fitti
Do NOT use Plumber’s Pipe Dope as it may cause cracking of the plastic components.
to plastic threads, wrap the entire threaded portion of the male fitting with one to two l
tape. Wind the tape clockwise as you face the open end of the fitting, beginning at the end of the fitting. It is only nece
to tighten fittings enough to prevent leakage. Tighten fitting by hand and then use a tool to engage fitting an add
tape as friction is reduced considerably;
. If leaks occur, remove connector, clean off old
Fittings restrict flow. For better efficiency, use the fewest possible fittings (but at least two suction outlets). Avoid f
-entrapping suction fitting in
WARNING
–
All electrical wiring MUST be in conformance with all applicable local codes,
regulations, and the National Electric Code (NEC).
WARNING
- Ground and bond motor before connecting t
ground and bond pump motor can cause serious or fatal electrical shock hazard.
To avoid dangerous or fatal electrical shock, turn OFF power to motor before working
onnections.
Fire Hazard
that the electrical supply available agrees with the motor’s voltage, phase, and cycle, and that the wire size is adequate fo
rating and distance from the power source.
Use copper conductors only.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
www.haywardflowcontrol.com
MUM INLET PIPING SIZE CHART
Minimum Suction Pipe
in. [mm] *
It is recommended that a minimum length of straight piping (s
to 5 pipe size diameters, be used between the pump suction inlet and any plumbing fittings (elbows, valves, etc.).
Hazardous Pressure.
Pumps, filters, and other equipment/ components of a
erate under pressure. Incorrectly installed and/or improperly tested equipment and/or
components may fail resulting in severe personal injury or death.
to seal threaded connections on molded plastic components. All plastic fitti
Do NOT use Plumber’s Pipe Dope as it may cause cracking of the plastic components.
to plastic threads, wrap the entire threaded portion of the male fitting with one to two l
tape. Wind the tape clockwise as you face the open end of the fitting, beginning at the end of the fitting. It is only nece
to tighten fittings enough to prevent leakage. Tighten fitting by hand and then use a tool to engage fitting an add
tape as friction is reduced considerably;
. If leaks occur, remove connector, clean off old PTFE tape, re
Fittings restrict flow. For better efficiency, use the fewest possible fittings (but at least two suction outlets). Avoid f
entrapping suction fitting in
All electrical wiring MUST be in conformance with all applicable local codes,
regulations, and the National Electric Code (NEC).
Ground and bond motor before connecting t
ground and bond pump motor can cause serious or fatal electrical shock hazard.
To avoid dangerous or fatal electrical shock, turn OFF power to motor before working
Fire Hazard - match supply voltage to motor nameplate voltage.
that the electrical supply available agrees with the motor’s voltage, phase, and cycle, and that the wire size is adequate fo
Use copper conductors only.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
www.haywardflowcontrol.com
It is recommended that a minimum length of straight piping (shown as “L” in above diagram), equivalent
to 5 pipe size diameters, be used between the pump suction inlet and any plumbing fittings (elbows, valves, etc.).
Pumps, filters, and other equipment/ components of a
erate under pressure. Incorrectly installed and/or improperly tested equipment and/or
components may fail resulting in severe personal injury or death.
to seal threaded connections on molded plastic components. All plastic fitti
Do NOT use Plumber’s Pipe Dope as it may cause cracking of the plastic components.
to plastic threads, wrap the entire threaded portion of the male fitting with one to two l
tape. Wind the tape clockwise as you face the open end of the fitting, beginning at the end of the fitting. It is only nece
to tighten fittings enough to prevent leakage. Tighten fitting by hand and then use a tool to engage fitting an add
tape as friction is reduced considerably;
do NOT over
tape, re-wrap with one to two additional layers of
Fittings restrict flow. For better efficiency, use the fewest possible fittings (but at least two suction outlets). Avoid f
entrapping suction fitting in system (multiple drains)
All electrical wiring MUST be in conformance with all applicable local codes,
regulations, and the National Electric Code (NEC).
Ground and bond motor before connecting t
ground and bond pump motor can cause serious or fatal electrical shock hazard.
To avoid dangerous or fatal electrical shock, turn OFF power to motor before working
match supply voltage to motor nameplate voltage.
that the electrical supply available agrees with the motor’s voltage, phase, and cycle, and that the wire size is adequate fo
Use copper conductors only.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
hown as “L” in above diagram), equivalent
to 5 pipe size diameters, be used between the pump suction inlet and any plumbing fittings (elbows, valves, etc.).
Pumps, filters, and other equipment/ components of a
erate under pressure. Incorrectly installed and/or improperly tested equipment and/or
components may fail resulting in severe personal injury or death.
to seal threaded connections on molded plastic components. All plastic fittings must be new or thoroughly
Do NOT use Plumber’s Pipe Dope as it may cause cracking of the plastic components.
to plastic threads, wrap the entire threaded portion of the male fitting with one to two l
tape. Wind the tape clockwise as you face the open end of the fitting, beginning at the end of the fitting. It is only nece
to tighten fittings enough to prevent leakage. Tighten fitting by hand and then use a tool to engage fitting an add
do NOT over-tighten fitting or you may cause
wrap with one to two additional layers of
Fittings restrict flow. For better efficiency, use the fewest possible fittings (but at least two suction outlets). Avoid f
(multiple drains) or double suction (skimmer and
All electrical wiring MUST be in conformance with all applicable local codes,
Ground and bond motor before connecting to electrical power supply. Failure to
ground and bond pump motor can cause serious or fatal electrical shock hazard.
To avoid dangerous or fatal electrical shock, turn OFF power to motor before working
match supply voltage to motor nameplate voltage.
that the electrical supply available agrees with the motor’s voltage, phase, and cycle, and that the wire size is adequate fo
1-888-HAY
ISHCP3000FC
hown as “L” in above diagram), equivalent
to 5 pipe size diameters, be used between the pump suction inlet and any plumbing fittings (elbows, valves, etc.).
Pumps, filters, and other equipment/ components of a
erate under pressure. Incorrectly installed and/or improperly tested equipment and/or
ngs must be new or thoroughly
Do NOT use Plumber’s Pipe Dope as it may cause cracking of the plastic components.
to plastic threads, wrap the entire threaded portion of the male fitting with one to two l
tape. Wind the tape clockwise as you face the open end of the fitting, beginning at the end of the fitting. It is only nece
to tighten fittings enough to prevent leakage. Tighten fitting by hand and then use a tool to engage fitting an add
tighten fitting or you may cause
wrap with one to two additional layers of
Fittings restrict flow. For better efficiency, use the fewest possible fittings (but at least two suction outlets). Avoid f
or double suction (skimmer and
All electrical wiring MUST be in conformance with all applicable local codes,
o electrical power supply. Failure to
ground and bond pump motor can cause serious or fatal electrical shock hazard.
Do NOT ground to a
To avoid dangerous or fatal electrical shock, turn OFF power to motor before working
match supply voltage to motor nameplate voltage.
that the electrical supply available agrees with the motor’s voltage, phase, and cycle, and that the wire size is adequate fo
Y-INDL (1-888-429
ISHCP3000FC Rev A 1
Pg.
hown as “L” in above diagram), equivalent
to 5 pipe size diameters, be used between the pump suction inlet and any plumbing fittings (elbows, valves, etc.).
Pumps, filters, and other equipment/ components of a
erate under pressure. Incorrectly installed and/or improperly tested equipment and/or
ngs must be new or thoroughly
Do NOT use Plumber’s Pipe Dope as it may cause cracking of the plastic components.
to plastic threads, wrap the entire threaded portion of the male fitting with one to two layers of
tape. Wind the tape clockwise as you face the open end of the fitting, beginning at the end of the fitting. It is only necessary
to tighten fittings enough to prevent leakage. Tighten fitting by hand and then use a tool to engage fitting an additional 1 ½
tighten fitting or you may cause
wrap with one to two additional layers of PTFE tape,
Fittings restrict flow. For better efficiency, use the fewest possible fittings (but at least two suction outlets). Avoid fittings
or double suction (skimmer and
All electrical wiring MUST be in conformance with all applicable local codes,
o electrical power supply. Failure to
Do NOT ground to a
To avoid dangerous or fatal electrical shock, turn OFF power to motor before working
match supply voltage to motor nameplate voltage.
Insure
that the electrical supply available agrees with the motor’s voltage, phase, and cycle, and that the wire size is adequate for the
9-4635)
1/30/16
. 7 of 16
ssary
tape,
or double suction (skimmer and
o electrical power supply. Failure to
To avoid dangerous or fatal electrical shock, turn OFF power to motor before working
Insure
r the
