background image

 

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 

 

 

1-888-HAY-INDL (1-888-429-4635) 

ISHCP3000FC Rev A 11/30/16

 

Pg. 5 of 16

 

www.haywardflowcontrol.com 

Hayward Flow Control 

 

 

WARNING

 

– To reduce the risk of electric shock replace damaged wiring immediately.   

 

WARNING

 

– 

Ground all electrical equipment before connecting to electrical power supply.  Failure to ground all electrical 

equipment can cause serious or fatal electrical shock hazard.

 

 

WARNING

 –

 

Do NOT ground to a gas supply line.

 

 

WARNING

 

– To avoid dangerous or fatal electrical shock, turn OFF power to all electrical equipment before working on 

electrical connections. 

 

WARNING 

– Failure to bond all electrical equipment to system structure will increase risk for electrocution and could result in 

injury or death.  To reduce the risk of electric shock, see installation instructions and consult a professional electrician on how to bond all 
electrical equipment.  Also, contact a licensed electrician for information on local electrical codes for bonding requirements. 

 

WARNING 

– Risk of Electric Shock.  Connect only to a branch circuit protected by a ground-fault circuit-interrupter (GFCI).  

Contact a qualified electrician if you cannot verify that the circuit is protected by a GFCI. 

 

WARNING 

– Risk of Electric Shock .  The electrical equipment must be connected only to a supply circuit that is protected by a 

ground-fault circuit-interrupter (GFCI).  Such a GFCI should be provided by the installer and should be tested on a routine basis.  To test 
the GFCI, push the test button.  The GFCI should interrupt power.  Push reset button.  Power should be restored.  If the GFCI fails to 
operate in this manner, the GFCI is defective.  If the GFCI interrupts power to the electrical equipment without the test button being 
pushed, a ground current is flowing, indicating the possibility of an electrical shock.  Do not use this electrical equipment.  Disconnect the 
electrical equipment and have the problem corrected by a qualified service representative before using.

 

 

CAUTION 

–  This pump has been evaluated for use with water only. 

 

ATTENTION - 

Cette pompe a été évalué pour une utilisation avec de l'eau seulement. 

 

 

SAVE THESE INSTRUCTIONS 

  

 

 

Содержание LifeStar MV Series

















Отзывы: