Haws 9035 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 26

background image

12/19

Model 9035

Page 21 of 26

Step 28 / Panel Mounting:

All panels must be fastened to the outside of the frame using the mounting

hardware supplied by Haws for this unit. This step defines the components and method for attaching the
aluminum panels to the frame. (See Figure 27.) Each connection consists of a Screw, Washer, Clamp, and Nut.
These are grouped together to comprise a Mounting Hardware Set and are hereafter referred to as an

“

MH Set

”.

The basic tools required to install the panels are as follows: Two (2)

7/16” (or adjustable) Crescent Wrenches –

one to hold the nuts in place, and one to turn the screws.

(Otherwise, A power drill (or ratchet) with a

7/16”

socket in place of one of the wrenches, used to turn the screws, greatly speeds up the installation.)

FIGURE 27

Step 29:

Fasten two (2) Roof Panels to the frame using ten (10) MH Sets per panel. (See Figures 28A & 28B.)

(Note that the roof panel mounting holes are aligned at the roof apex such that the loop clamps are offset and
do not interfere. The roof panels can be flipped/rotated in multiple ways to attain this condition.)

FIGURE 28A FIGURE 28B

Step 30:

Fasten two (2) Triangular Panels to the frame using ten (10) MH Sets per panel.

(See Figures 29A & 29B.)

FIGURE 29A FIGURE 29B

82X 1/4-20 SST

Nylon Insert

Hex Head Nut

82X 1.32 ID

(For 1.00” Pipe)

Loop Clamp

82X 1/4" ID SST

Flat Washer

82X 1/4-20 UNC-

2A X 1.00”

18-8 SST Hex Head

Machine Screw

(5mm Thick

Dibond Panel )

(1.00” SCHED 40 Steel Pipe)

2X Roof Panels

10X MH Sets / Panel (20 total)

Front Side

2X Triangular Panels

Front Side

7X MH Sets / Panel (14 total)

Rear Side Panel not shown.

«
...
19
20
21
22
23
...
»

Содержание 9035



























Отзывы:

Нет отзывов

Похожие инструкции для 9035

Бренд: AMERICANA OUTDOORS Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды