Haws 9035 Скачать руководство пользователя страница 18

Страница: 18 / 26

12/19

Model 9035

Page 18 of 26

Step 23:

Install one (1) Roof End Support onto the exposed section of pipe at the rear of the unit. Slide the right

side roof end support to the rear side and rotate both roof end supports such that the swivel tee thru holes

’ axes

are roughly aligned and the swivel tee surfaces mate. (See Figure 20A.) Tighten the swivel tee set screws at the
49.12” pipes.

FIGURE 20A

(Figure 20B shows a wider view of how the unit should look when the rear side roof support ends are properly
installed and arranged,)

FIGURE 20B

Step 24:

Measure 24 9/16" from the outer surfaces of the left rear & right rear swivel tee thru holes, along the

center of each

49 .12” pipe, and mark a line on each pipe with a felt-tip marking pen. (See Figures 21A & 21B.)

(These marks represent the mid-points of the

49.12” pipes.)

FIGURE 21A FIGURE 21B

Step 25:

Slide the two Roof Center Supports along the

49.12” pipes such that the rear edge of one tee and the

front edge of the other tee align with the marked lines from Step 24. Rotate the roof center supports such that
the thru holes

’ axes are roughly aligned and the swivel tees mate. (See Figure 22.) Tighten the swivel tee set

screws at the

49.12” pipes.

FIGURE 22

2X Swivel Tee

Thru Holes

Roof End Support

Exposed End of

49.12” Pipe

2X Swivel Tee

Thru Holes

2X Roof End

Supports

Rear Side

Mark at 24 9/16”

from Rear Side

Rear Side

Mark at 24 9/16”

from Rear Side

Roof Center Support

2X Swivel Tee Thru Holes

Roof Center Support

Содержание 9035



























Результаты поиска

Содержание 9035

Отзывы:

Похожие инструкции для 9035

Бренды по названию

Популярные бренды

Haws 9035, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 9035

Отзывы:

Похожие инструкции для 9035

Бренды по названию

Популярные бренды