Haws 9035 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 26

background image

12/19

Model 9035

Page 16 of 26

Step 18:

Create four (4) Roof End Support assemblies: Fully insert four (4) 22.25" Pipes into the pipe cup end of

eight (8) Short Swivel Tee-Pair fitting halves. Orient the swivel tees such that the set screws at both ends are
facing upwards and perpendicular to the ground. (See Figure 16.) Tighten the swivel tee set screws.

Step 19:

Create two (2) Roof Center Support assemblies: Fully insert two (2) 23.75" Pipes into the pipe cup

ends of four (4) Short Tee fittings allowing for pass-through of adjoining pipe. Orient the tees such that the set
screws at both ends are facing upwards and perpendicular to the ground. (See Figure 16.) Tighten the tee set
screws.

FIGURE 16

Step 20

: Slide one (1) 49

.12” Pipe through the

right-side

swivel tee thru hole at the

rear

side of the unit. Push

the pipe two feet into the thru hole and install - with the set screws facing outward - one (1) Roof End Support
and one (1) Roof Center Support, onto the

49.12” pipe. Slide the 49.12” pipe to the front and through the right-

side swivel tee thru hole. (See Figure17A.) Flush the

49.12” pipe to the outer surface of the rear swivel tee and

tighten the swivel tee thru hole set screw only. (See Figure17B.)

FIGURE 17A FIGURE 17B

4X Roof End Supports

(Sub-Assemblies)

2X Roof Center Support

(Sub-Assemblies)

2X Short Tees

2X Short Tees

4X Short Swivel Tees

4X Short Swivel Tees

4X 22.2

5” Pipes

4X 23.75” Pipes

Roof Center

Support

Roof End

Support

49.12” Pipe

Rear Side

of Unit

Right Side

of Unit

Rear Side Swivel Tee

Thru Hole & Setscrew

Right Side

of Unit

«
...
14
15
16
17
18
...
»

Содержание 9035



























Отзывы:

Нет отзывов

Похожие инструкции для 9035

Бренд: ClearSpan Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды