Haulotte HA20RTJ O Скачать руководство пользователя

Страница: 84 / 112

4000388880

E 06 15

GB / USA

- Operation instructions

HA20RTJ - HA20RTJ O - HA20RTJ PRO - HA61RTJ O - HA61RTJ PRO

6.2 - H

YDRAULIC

OIL

External environmental conditions can reduce performance of the machine if the hydraulic oil
temperature does not reach its optimum range.

It is recommended to use the hydraulic oil according to weather condition. Refer to the table
below.

N.B.-:-I

RECOMMENDED

REPLACE

LOW

TEMPERATURE

OIL

THE

AMBIENT

TEMPERATURE

REACHES

+ 15°C (59°F). I

NOT

ADVISABLE

MIX

OILS

DIFFERENT

BRANDS

TYPES

6.3 - P

REHEATING

OPERATION

• Turn the power on by turning the ON/OFF seclector key switch ( 18 ) to the right.

• When the start / stop selector switch ( 230 ) at platform control box or ( 228 ) at ground

control box is activated, the orange LED ( 5 ) at ground control display panel and LED ( 102 )
at platform control display panel flashes, indicating that the engine is in automatic pre-
heating mode.

• Upon the extinction of this light ( 3 s to 15 s) at ground control box, the engine starts.

Environmental conditions

SAE Viscosity grade

Ambient temperature between - 15°C (5°F) and + 40°C (+ 104°F)

HV 46

Ambient temperature between - 35°C (- 31°F) and + 35°C (+ 95°F)

HV 32

Ambient temperature between 0°C (+ 32°F) and + 45°C (+ 113°F)

HV 68

Содержание HA20RTJ O

















































































































Результаты поиска

Содержание HA20RTJ O

Отзывы:

Похожие инструкции для HA20RTJ O

Бренды по названию

Популярные бренды

Haulotte HA20RTJ O, Руководство оператора

Результаты поиска

Содержание HA20RTJ O

Отзывы:

Похожие инструкции для HA20RTJ O

Бренды по названию

Популярные бренды