Haulotte HA20RTJ O Скачать руководство пользователя

Страница: 82 / 112

4000388880

E 06 15

GB / USA

- Operation instructions

HA20RTJ - HA20RTJ O - HA20RTJ PRO - HA61RTJ O - HA61RTJ PRO

5.6 - L

IFTING

OPERATION

During loading / unloading operation, if it becomes necessary to lift the machine using an
overhead crane, it is important to respect the following :
• Put the machine in stowed position, boom and arm fully retracted and lowered.

• Ensure the platform is empty.

• Rotate the turret and the jib to the configuration in the photos below.

• Lock the turret with turret locking pin.

• Verify that lifting accessories are in good operation and match the technical specifications

listed below. It is important that the lifting devices are attached only to the designated lifting
eyes.

• Each of the chains/slings used for lifting the machine must be adjusted to keep the machine

level and to minimize the risk of damage to the machine.

• Anchorage point for lifting are identified / labeled by the following symbol

• ONLY trained and authorized personnel should attempt to lift the machine.

P r o c e d u r e f o r t h e u s e o f s l i n g s

Never lift the machine with slings attached to counterweight.

Number of shackles

Number of slings

Length

Maximum load per sling and shackle

5 m (16 ft 5 in)

3000 daN (6744 lbf)

Содержание HA20RTJ O

















































































































Результаты поиска

Содержание HA20RTJ O

Отзывы:

Похожие инструкции для HA20RTJ O

Бренды по названию

Популярные бренды

Haulotte HA20RTJ O, Руководство оператора

Результаты поиска

Содержание HA20RTJ O

Отзывы:

Похожие инструкции для HA20RTJ O

Бренды по названию

Популярные бренды