HANYOUNG NUX TD300 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 52

HANYOUNG NUX TD300 Скачать руководство пользователя страница 6

7

2 Installation method

This is information for installation place and method of TD500 (2 loop temperature controller). So please

ready it before installation.

2.1 Installation place and caution notice

2.1.1 Installation place

● To avoid electric shock, please use it after installation to panel
● Please avoid installing the product for following places where

• People can touch terminal unconsciously
• Directly exposed to the mechanical vibration or impact
• Exposed to the corrosive gas or combustible gas
• It is exposed to mechanical shock or vibration
• Danger of corrosion or combustion of gas exist
• Temperature changes too frequently
• Temperature is either too high or too low
• It is exposed to direct rays
• It is exposed to electromagnetic waves too much
• Humid place
• It has many combustible objects
• It has dusts and salinity

2.1.2 Caution

●  The case of this controller is chrome-zinc plating and Bezel is made by ABS/PC anti-combustion
material but please not install it to the inflammable place. Especially please do not put it on the
inflammable products.
● Please keep it away from the machine or wires that can be cause of noise.
Especially, please have enough warn-up when you operate it under 10 ℃ temperature.
● Please install it on horizontally
● When you wire it, please cut out all of electric power.
●  This controller is operating in 100 - 240 V AC, 50-60 Hz without additional change.
If you use other voltage, it may case of fire and electric shock.
● Do not operate controller with wet hand, it may cause of electric shock.
● Please follow Safety Information to prevent any fire, electric shock and any damage.
● Please follow this manual for install and operation of this controller.
●  When you put to earth, please refer to install method. But do not it earth to gas pipes, phone lines
and lightning rods
● Please do not turn on power until you install all of parts
● Please do not block ventilating windows. It may cause of break down.
● The grade of over voltage is Catalogue

Ⅱ

and using environment is Degree

Ⅱ

هﺮﮐ

ﮓﻧﺎﯿﻧﺎﻫ

تﻻﻮﺼﺤﻣ

یرﺎﺼﺤﻧا

هﺪﻨﯾﺎﻧﻤ

ناﻮﯿﺳ

ﺖﮐﴍ

021-33989001

www.sivancarno.com

021-33989002

«
...
4
5
6
7
8
...
»

Содержание TD300





















































Отзывы:

Нет отзывов