Hantek HDG 2000 Series Скачать руководство пользователя страница 73

Страница: 73 / 111

SCPI Programming Reference

HDG2000 Series Arbitrary Waveform Generator



This setting is non-volatile; it will not be changed by power cycling or

*RST

CALibration:STORe

Takes calibration constants in volatile memory (

CALibration?

), and places them in nonvolatile

memory, where they will not be changed by power cycle.

Parameter

Typical Return

none

无

Store calibration constants into non-volatile memory: CAL:STOR

CALibration:VALue <value>

Specifies the value of the known calibration signal.

Parameter

Typical Return

Numeric, default 0

none



This setting is non-volatile; it will not be changed by power cycling or

*RST

5.2.6 COUNter Subsystem

COUNter ON|OFF

COUNter:MEASure?

COUNter:GATEtime

COUNter:GATEtime?

COUNter:TYPE

COUNter ON|OFF

Enable or disable frequency meter.

Parameter

Typical Return

ON|OFF, default OFF

ON , or OFF

COUNter ON

COUNter:MEASure?

Get current counter measurement value.

Parameter

Typical Return

Current frequency or counter

COUNter:GATEtime?

Set

GATEtime

Содержание HDG 2000 Series
















































































































Результаты поиска

Содержание HDG 2000 Series

Отзывы:

Hantek HDG 2000 Series, Руководство пользователя, Страница: 73 / 111

Результаты поиска

Содержание HDG 2000 Series

Отзывы: