Hantek HDG 2000 Series Скачать руководство пользователя страница 34

Страница: 34 / 111

Features and Function

HDG2000 Series Arbitrary Waveform Generator



To avoid multiple waveform changes, enable modulation after configuring the other modulation

parameters.



Front Panel:



SCPI:

SOURce<n>:MOD ON|OFF

SOURce<n>:MOD:TYPe AM|FM

Carrier Waveform Shape



AM or FM carrier shape: Sine (default), Square, Ramp, Pulse, Ramp, Noise or Arbitrary

waveform

You cannot use DC as the carrier waveform.



For FM, the carrier frequency must always be greater than or equal to the frequency deviation.

Attempting to set a deviation greater than the carrier frequency will cause the instrument to set

the deviation equal to the carrier frequency.



The carrier frequency plus the deviation cannot exceed the selected function's maximum

frequency plus 100 kHz.

Carrier Frequency

The maximum carrier frequency varies by function, as shown below. The default is 1 kHz for all

functions.

Function

Minimum Frequency

Maximum Frequency

Sine

1μHz

the highest frequency

Square

HDG2102B, HDG2082B,

HDG2062B, HDG2032B,

HDG2102C, HDG2072C,

HDG2052C , HDG2032C

1μHz ~ 30MHz

HDG2022B, HDG2012B,

HDG2002B

1μHz ~ the highest frequency

Ramp

HDG2102B, HDG2082B,

HDG2062B, HDG2032B,

HDG2102C, HDG2072C,

HDG2052C, HDG2032C

1μHz ~ 4MHz

HDG2022B, HDG2012B,

HDG2002B

1μHz ~ 3MHz

Содержание HDG 2000 Series
















































































































Результаты поиска

Содержание HDG 2000 Series

Отзывы:

Hantek HDG 2000 Series, Руководство пользователя, Страница: 34 / 111

Результаты поиска

Содержание HDG 2000 Series

Отзывы: