Hanseatic EKS 1800-35, Руководство по эксплуатации

Страница: 26 / 32

GB-3
54. Do not work with your body bent forwards.
55. Ensure that you are standing securely and do not
work on snow, ice or newly‑barked wood. Danger of
slipping!
56. Working on ladders, scaffoldings or trees is forbid‑
den.
57. Do not use chain saw above shoulder height.
58. Use the chain saw only to cut wood. It is abso‑
lutely forebidden to cut plastics or minerals (gas
concrete).
59. Ensure that the wood cannot twist while it is being
cut.
60. Never climb on a tree to cut wood.
61. Watch out for splintering wood. While you are sawing
you may be injured by flying wood chips.
62. Do not use the chain saw to lever or move the
wood.
63. Only cut with the lower section of the saw. The saw
will be repulsed towards you if you try and cut with
the upper section of the saw.
64. Ensure that the wood is free of stones, nails or other
foreign objects.
65. We recommend that first-time users are instructed
practically as to the correct use of the chain saw
and the required personal safety equipment by an
experienced operator; the cutting of round wood or
logs should be trained on a log stand or similar rack‑
type device first.
66. Keep the running chain saw from touching the
ground or wire fences. Do not cut thin wood or timber
that is already sawn into small pieces.
Starting up
1. Filling the oil tank (Fig. 1)
The chain saw must never be operated without sufficient
oil on the chain as this could cause damage to the chain,
blade or motor. No claims for guarantee can be accepted
if damage occurs when the device is being operated
without chain oil.
Please use only biologically-based chainsaw oil, i.e.
oil which is 100% biologically decomposable.
Biological chainsaw oil should be available everywhere
at your local specialist dealer.
Do not use old oil. This will damage the chainsaw and will
also lead to loss of the guarantee.
• Before filling the oil tank, pull out the mains plug
• Open the twist cap and place safely aside so that the
sealing ring in the tank cap does not get lost.
• Fill approx. 150 ml oil into the tank using a funnel and
screw on the tank cap tightly once more.
• The oil level can be seen in the inspection window. If
you plan not to use the machine for a longer period,
you should remo ve the chain oil from the oil tank.
• The oil tank should also be emptied before the chain ‑
saw is transported or dispatched.
• Check correct functioning of the chainsaw before com-
mencing work. Switch on the saw with cutting fittings
assembled and hold over a bright background at a safe
distance (Be careful not to come in contact with the
ground !). An track of oil will show you that the chain is
sufficiently lubricated.
• After use, lay the chainsaw horizontally on some absor-
bing surface. The oil spread on the blade, chain and
drive may lead to some further dripping of oil.
2. Assembling the blade and chain (Fig. 2 ‑ 4)
CAUTION ! Risk of injury ! Always use safety
gloves when assembling the chain !
• Lay the chainsaw on a stable base.
Release and remove the securing nut. Remove protec‑ •
tion cap first.
Pull off the pinion lid •
• Lay the saw chains onto the blade and observe the di ‑
rection of the chain. The cutting teeth must be point-
ing forward on the top of the blade (see fig. 4).
• Lay the unattached end of the saw chain over the chain
drive wheel (see fig.2, B) and the blade 5 with the elon ‑
gated hole over the blade guide and chain tensioning
bolt
• Observe that the chain tensioning bolt is sitting exactly
in the small opening in the blade (see fig.2, A). It must
be visible through the opening.
• Now shove the blade together with the chain forwards.
Observe that all chain links are positioned exactly in
the blade grove and that the saw chain is running pre‑
cisely around the chain drive wheel.
• Replace the pinion lid and press it tightly until secure.
• Replace the securing nut. The securing nut should
initially only be tightened by hand.
• Tighten the chain. To do this, turn the chain tension ‑
ing screw (see Fig.3, C) in a clockwise direction. The
chain should be tensioned so that it can still be raised
approx. 3 mm in the middle of the blade (Fig. 4).
• Finally, tighten the securing nut using a socket spanner.
Put the protection cap on the nut.
The tension in the chain has a major effect on the
service life of the cutting fittings, and must therefore
be checked regularly. When the chain warms up to
operating tempe‑rature it will expand and must be
retightened. A new saw chain will have to be tightened
more frequently until it has reached its full length.
CAUTION: During the running-in period, the chain
must be more frequently tightened. The chain
must be immediately retightened if it shakes or
leaves the grove !
To tighten the chain, loosen the nut. Then turn the chain
tensioning screw (see Fig.3, C) on the front of the chain‑
saw in a clockwise direction.Keep tightening the chain
until it can be raised in the middle of the blade by approx.
3 mm, as shown in Fig. 4.
3. Connecting the chainsaw (Fig. 5)
We recommend to operate the chain saw in connec-
tion with a residual current operated device with a
maximum breaking current of 30mA.
This device is designed to be operated on a mains supply
with a system impedance Z max at the point of connec‑
tion (house service connection) of max. 0.4 Ohm. The
user must ensure that the device is only operated on an
electricity supply system meeting these requirements. If
required, system impedance data may be obtained from