Hanna Instruments HI98190 Скачать руководство пользователя страница 13

Страница: 13 / 60

OPERA

TIONAL GUIDE

The ISE reading will be displayed along with the current temperature reading.

The

“ATC”

(or

“MTC”

) message is turned off because ppm readings are not temperature

compensated.
In order to take accurate ISE measurements, make sure that the appropriate ISE electrode type and
ISE unit were set in

SETUP

menu and the instrument was calibrated (see ISE CALIBRATION for

details, page 25).

Notes: When the reading is out of range, the display will flash the closest full-scale value.

The instrument will display “----” on the primary LCD if it is not calibrated. Perform at least

a one point calibration in order to take ISE measurements.

Changing the ISE electrode or the ion charge will need ISE range calibration.

TEMPERATURE MEASUREMENTS

For

HI98190

the temperature sensor is connected through DIN socket.

Connect the temperature connector to the appropriate socket (

HI98191

). Immerse the pH electrode

into the sample and allow the reading on the secondary LCD to stabilize.

Note: The temperature can be displayed in Celsius degrees (

C) or in Fahrenheit degrees

(

F) (see SETUP for details, page 31).

BACKLIGHT FEATURE

The instrument is provided with a Backlight feature, which can be easily toggled on and off through
the keyboard by pressing

LIGHT

Note: The backlight automatically shuts off after a set period (see SETUP for details,

page 31) with no buttons pressed.

Содержание HI98190





























































Результаты поиска

Содержание HI98190

Отзывы:

Похожие инструкции для HI98190

Бренды по названию

Популярные бренды

Hanna Instruments HI98190, Инструкция по эксплуатации

Результаты поиска

Содержание HI98190

Отзывы:

Похожие инструкции для HI98190

Бренды по названию

Популярные бренды