Hanna Instruments HI98190 Скачать руководство пользователя страница 58

Страница: 58 / 60

IMPORTANT

: After performing any of the cleaning procedures, rinse the electrode thoroughly with

distilled water, refill the reference chamber with fresh electrolyte (not necessary for gel‑filled elec‑
trodes) and soak the electrode in

HI70300

HI80300

Storage Solution for at least 1 hour before

taking measurements.

TROU

G G

SYMPTOMS

PROBLEM

SOLUTION

Slow response/excessive drift.

Dirty pH electrode.

Soak the electrode tip in

HI7061

solution for 30 minutes and then
follow the Cleaning Procedure.

Reading fluctuates up and down (noise). Clogged/dirty junction. Low

electrolyte level (refillable
electrodes only).

Clean the electrode. Refill with fresh
electrolyte (refillable electrodes
only).

Display shows blinking full scale value.

Reading out of range.

Check that sample is within measur‑
able range

mV scale out of range.

Dry membrane or dry junction.

Soak electrode in

HI70300

storage

solution for at least 30 minutes.

Display shows symbol in front of
temperature reading.

Out of order or missing tempera‑
ture probe.

Replace temperature probe or check
the connection.

Display shows

"Clean electrode"

blinking.

Difference between new and
previous calibration has been
detected.

Clean electrode and recalibrate.
If the problem remains, check the
buffer solutions.

Meter does not work with temperature
probe.

Broken temperature probe.

Replace temperature probe.

Meter fails to calibrate or gives faulty
readings.

Broken pH electrode.

Replace electrode.

Error messages are displayed during pH
calibration procedure.

Wrong or contaminated buffer,
electrode dirty or broken.

Check that buffer solution is correct
and fresh.

Meter shuts off.

Dead accumulators; Auto‑off
feature is enabled: in this case,
meter shuts off after selected
period of non‑use.

Recharge accumulators or replace
batteries; Press

ON/OFF.

"Errxx"

message at start up.

Internal error.

Contact your dealer or any Hanna
Service Center.

The instrument does not start when
pressing

ON/OFF

Initialization error.

Press and hold down

ON/OFF

for

about 20 seconds or disconnect and
then connect one accumulator.

Содержание HI98190





























































Результаты поиска

Содержание HI98190

Отзывы:

Похожие инструкции для HI98190

Бренды по названию

Популярные бренды

Hanna Instruments HI98190, Инструкция по эксплуатации

Результаты поиска

Содержание HI98190

Отзывы:

Похожие инструкции для HI98190

Бренды по названию

Популярные бренды