Hanna Instruments HI98190 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 60

background image

54

Notes: “Err8” is sent if the instrument is not in measurement mode.

“Err6” is sent if the requested range is not available.

“Err4” is sent if the requested set parameter is not available.

“Err3” is sent if the Log on demand is empty.

“Err9” is sent if the battery power is less than 30%.

Invalid commands will be ignored.

To replace the batteries, follow the next steps:
• Turn OFF the instrument.
• Open the battery compartment by removing the four screws from the back of the instrument.
• Remove the old batteries.
• Insert four new 1.5V AA batteries in the battery compartment while paying attention to the correct
polarity.
• Close the battery compartment using the four screws.
If the battery capacity is less than 20 % the serial communication and the backlight feature are not
available.

BA

TTERIES REPLACEMENT

Note: The instrument is provided with the BEPS (Battery Error Prevention System) feature,

which automatically turns the instrument off when the batteries level is too low to ensure

reliable readings.

«
...
52
53
54
55
56
...
»

Содержание HI98190





























































Отзывы:

Нет отзывов

Похожие инструкции для HI98190

Бренд: TaiDoc Страницы: 31

Бренд: BANTE inststruments Страницы: 15

Бренд: 3Bays Страницы: 21

Бренд: jenway Страницы: 52

WALLACE & TIERNAN P7 ADVANCED

Бренд: Evoqua Страницы: 98

Бренд: Keller Страницы: 4

Бренд: Conrad Electronic Страницы: 38

Бренд: Tektronix Страницы: 20

Arrow Mobile Android

Бренд: MADDALENA Страницы: 12

Бренд: Fluke Страницы: 6

AUER Atemluft 300 bar

Бренд: MSA Страницы: 52

Бренд: Kawai Страницы: 10

Бренд: YUSHI Страницы: 15

Бренд: Fluke Страницы: 97

Бренд: Young Страницы: 7

ProSense LPM1 Series

Бренд: Automation Direct Страницы: 29

Бренд: Hesai Страницы: 8

VideoScope Plus

Бренд: LaserLiner Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды