Hangar 9 Advance 40 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 36

background image

6

Step 1.

From your radio system box, remove one servo and the

servo mounting hardware—four rubber grommets, four brass
eyelets and four servo screws. Prepare the servo by installing the
four rubber grommets and eyelets in one servo as shown in the
photo below. The grommets insert onto the servo tabs and then
the eyelets are inserted from the bottom through the grommets.

The grommet installation is fairly simple. However, if you need
any additional help for this installation, please refer to your radio
system instruction manual.

Step 2.

Prior to assembling the wing, deflect the aileron control

surfaces by hand to loosen the hinges so the controls operate
smoothly.

• Wing halves (left and right)
• Wing joiner (wing brace)
• Wing joint tape
• One servo with mounting hardware (4 rubber grommets,

4 eyelets and 4 long servo screws—included with the
radio system)

• Aileron linkages with clevis attached (2)—these are the

shortest two linkages in the kit

• Aileron connectors (2)

Note:

On some Advance 40 kits,

these may already be attached to the aileron torque rods.

• Fuel tubing (2)

• 15-minute epoxy (included in kit)
• Rubbing alcohol
• Paper towels
• Epoxy mixing sticks (optional)
• Ruler
• Pencil
• Masking tape
• Wax paper (optional)
• Fuel tubing pieces (5mm long) (2)

Parts and Supplies Needed

Stage 1—Assembling the Wing

Fuel tubing

«
...
4
5
6
7
8
...
»

Содержание Advance 40





































Отзывы:

Нет отзывов

Похожие инструкции для Advance 40

Бренд: Bachmann Страницы: 12

Бренд: FB Jets Страницы: 39

Бренд: Parkside Страницы: 40

Бренд: Winfun Страницы: 16

Бренд: Faller Страницы: 4

Jungle Gym: Step & Count Kangaroo

Бренд: VTech Страницы: 11

E 50/BR 150 22154

Бренд: Trix Страницы: 40

3-IN-1 CLASSIC AMUSEMENT PARK

Бренд: K'Nex Страницы: 24

PENNSYLVANIA K4 STREAMLINER

Бренд: Lionel Страницы: 2

My Real Jam Active Play Music

Бренд: Little Tikes Страницы: 2

Бренд: Lionel Страницы: 20

Бренд: Ripmax Страницы: 10

Бренд: Tumama Kids Страницы: 30

Star Wars 75060

Бренд: LEGO Страницы: 307

Thunderbolt Strike Roller Coaster

Бренд: K'Nex Страницы: 44

75005 Pocket Poker

Бренд: Radica Games Страницы: 2

Бренд: PARKZONE Страницы: 24

Бренд: Eduard Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды