Hangar 9 Advance 40 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 36

Hangar 9 Advance 40 Скачать руководство пользователя страница 23

23

Step 1.

On the front of the Advance 40 is the pre-attached

engine mount (HAN40M). Unscrew the engine mounting
hardware (engine clamp bolts and clamps) from the engine
mount. Retain the hardware as we’ll be using it to mount the
engine in place.

Stage 6—Installing the Engine

• .40 - .48 size 2-cycle engine with muffler or .50 - .56 size

4-stroke engine with muffler

• Engine mount with mounting hardware (the mounting

hardware is pre-installed on the engine mount)

• Fuselage assembly
• Fuel tubing piece (5mm) (1)

Parts Needed

Fuel tubing

Place the engine on the engine mount and loosely clamp the
engine in place using the provided mounting hardware.

Note:

The knurled (checkered) side of the clamps faces
down, and it’s a good idea to use thread lock on the
bolts before installing the nuts.

Slide the engine as far forward as it will go and center the
engine, then tighten the screws until they become snug.

Note:

Be sure the screws that hold the clamp over the engine
mounting lugs are tightened very securely.

«
...
21
22
23
24
25
...
»

Содержание Advance 40





































Отзывы:

Нет отзывов