Hangar 9 Advance 40 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 36

background image

21

Step 1.

Rest the wing upside down with 1/2 the wing and the

aileron linkages hanging off the edge of the work table. Locate
the hardwood blocks in each wing panel where the landing gear
will be mounted. Place one of the main landing gears into the
pre-cut slot. The short 90° bend is inserted onto the hardwood
block installed in the wing.

Note:

You will put a slight bend in the landing gear straps
when you tighten them down on the wing. Push down
firmly on the screw when tightening to self tap the
screw into the hardwood.

Use two landing gear straps and four screws to mount the main
gear to the wing panel. Repeat the process for the other main gear.

Stage 5—Installing the Landing Gear

• Wing
• Fuselage
• Main wheels 2-1/2

′′

(2)

• Main landing gear (2)
• Landing gear straps (4)
• Wood screws (8)

• Nose wheel landing assembly
• Steering arm with screw
• Spring
• Collar with screw (2)
• Thread lock

Parts Needed

Landing Gear Straps

Main Landing Gear

Main Wheels

Nose Wheel

Wood Screws

Nose Gear

Steering Arm

Thread lock

Wheel Collars

Insert short end

in wing

«
...
19
20
21
22
23
...
»

Содержание Advance 40





































Отзывы:

Нет отзывов

Похожие инструкции для Advance 40

Бренд: a2pro Страницы: 11

Бренд: T-Motor Страницы: 2

Бренд: Idena Страницы: 3

Flyeaglejet AT3

Бренд: Fly Eagle Jet Страницы: 9

Бренд: marklin Страницы: 28

3-IN-1 CLASSIC AMUSEMENT PARK

Бренд: K'Nex Страницы: 24

Lights & Sounds

Бренд: Learning Resources Страницы: 2

Бренд: Herr Страницы: 16

Bear s Baby Laptop

Бренд: VTech Страницы: 10

Бренд: Zapf Creation Страницы: 76

Бренд: Capricorn Страницы: 63

Бренд: Vortex-RC Страницы: 35

Smart Start Future

Бренд: VTech Страницы: 16

Carry & Go Track Table 21802

Бренд: Simplay3 Страницы: 2

3-STALL ROUNDHOUSE

Бренд: Faller Страницы: 16

Бренд: GRAUPNER Страницы: 8

Бренд: marklin Страницы: 32

Panther Ausf. D Zimmerit Vertical

Бренд: Eduard Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды