Hangar 9 Advance 40 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 36

background image

26

Note:

You can thread the antenna through the tube, but this
is a time consuming process that’s not necessary.
Rubber banding the antenna to the tube is just as
effective, however it’s not as neat.

Installing the Antenna

Unchord the receiver and the antenna wire. Locate the antenna
tube included with the Advance 40. Pull about 1

′′

of antenna wire

past the end of the antenna tube and secure by wrapping a
rubber band around the tube to hold the antenna in place. Insert
the antenna tube through the back of the fuselage. Tuck the front
of the tube behind the servos in the fuselage.

You will need to purchase the appropriate propeller for your
particular engine. If you have a .40 size engine, a 10

×

6

propeller will work. For a .46 size engine, an 11

×

6 propeller is

the correct propeller.

Unscrew the prop nut from the engine and install the spinner
back plate, then the propeller, then the prop washer. Securely
tighten the prop nut using a 4-way or crescent wrench. Now
install the spinner using the two Phillips head screws provided.

Installing the Propeller

«
...
24
25
26
27
28
...
»

Содержание Advance 40





































Отзывы:

Нет отзывов

Похожие инструкции для Advance 40

Lancaster B Mk.II bomb bay

Бренд: Eduard Страницы: 2

SURPRISE 918230C3

Бренд: BABY born Страницы: 4

Бренд: Tronhelicopters Страницы: 43

Lolo's Meowsical Mat

Бренд: B.toys Страницы: 2

Bristol Trawler

Бренд: AquaCraft Страницы: 8

Бренд: Eurocopter Страницы: 58

Бренд: Dancing Wings Hobby Страницы: 6

INTERACTIVE NODDY CAR

Бренд: LEXIBOOK Страницы: 33

PICHLER Beechcraft T-34C TURBO MENTOR

Бренд: VQ Radio Control Model Страницы: 12

Touch & Explore Activity Table 5408

Бренд: VTech Страницы: 13

Seenotrettungsboot

Бренд: GRAUPNER Страницы: 30

Бренд: LEGO Страницы: 176

Бренд: Zhejiang Jiajia Ride-On Co. Страницы: 27

KOKUYO Flair Klixi Mixi

Бренд: PREZIOSI Страницы: 6

T-34C TURBO MENTOR

Бренд: PURSUIT Страницы: 198

AERO SUBARU 30EP

Бренд: KK Hobby Страницы: 4

Wireless Plus Set Duo 20010109

Бренд: Carerra Страницы: 52

Бренд: Totem Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды