HAMPTON BAY H35-10 Скачать руководство пользователя страница 11

Страница: 11 / 52

Hampton® H35-10 Direct Vent Freestanding Gas Stove

installation

OPTIONAL FAN INSTALLATION

H35

919-520a

04.13.15

OPTIONAL FAN INSTALLATION

Remove

Loosen

Fan Installation Kit Includes:

1- Fan Assembly c/w green ground wire attached

1- Fan Grey Cable attached to the Fan Assembly

1- Small Plastic Grommet

1- Big Plastic grommet

Remove the rear access panel on the back of the unit by removing 3 top

screws and loosening the bottom 3 screws.

NOTE: DO NOT damage, cut or remove the 3” aluminum air

intake pipes.

Install fan onto the 2 pins on the base panel. Fan Grey cable is already

attached to the fan assembly.

Connect the green wire to the grounding lug.

Run the Fan Grey wire through the large grommet on the base panel

to the bottom of the unit.

Open the bottom cover of the unit by loosening the 2 screws and

removing one from the left side of the unit (when facing back of
the unit).

Run the fan grey wire through the small grommet power cord from
the valve cover plate to the base panel through the large grommet.

Attach the connectors (black and red) of Fan Grey wire to the

IFC connectors (black and red).

NOTE: Do remember to follow the wire color code, i.e., balck

to black and red to red). Refer to the picture above.

Reinstall the bottom cover of the unit with 1 screw at the left side

of the unit (when facing back of the unit) and tightening the 2

screws at the back.

10.

Reattach the rear panel cover with 3 screws at the top of the

cover and tightening the 3 at the bottom of the panel.

11.

Reconnect gas and power supply.

12.

To remove fan-reverse steps.

NOTE:

•

120 Volt AC power is needed for the fan switch and blower.

•

Unit must be grounded at all times.

•

Do not cut the ground terminal off under any circumstances.

Large Grommet

Remove this screw

Connectors

Small Grommet

WARNING: Electrical Grounding Instructions

This appliance is equipped with a three pronged (ground-

ing) plug for your protection against shock hazard and

should be plugged directly into a properly grounded three-

prong receptacle. Do not cut or remove the grounding

prong from this plug.

Shut off gas and electrical supply.

Thermostat (Optional)

(Millivolt)

Содержание H35-10





















































Результаты поиска

Содержание H35-10

Отзывы:

Бренды по названию

Популярные бренды

HAMPTON BAY H35-10, Инструкция для владельца и по установке

Результаты поиска

Содержание H35-10

Отзывы:

Бренды по названию

Популярные бренды