Page 27
keyboard replace two screws in back of console first, leaving
them loose until remaining screws are replaced.)
3–12 SWELL ASSEMBLY
To remove swell assembly, perform steps a. through d. If
replacement of assembly is required, perform step e.
a. Remove two leads with white coded ends from preamplifier
and main amplifier.
b. Remove four wood screws securing swell housing cover to
case and lift out cover.
c. Remove four screws securing swell pedal assembly to case
work. Swell assembly is now loose and can be picked up and
removed from back.
d. Swell potentiometer can be removed at this time if necessary
and will require an Allen
1/16
” wrench.
e. Replacement for more dependable swell operation can be
made by ordering Part Number 123–000021 from the factory,
and proceeding as follows:
1. Remove Expression Control housing.
2. Unplug long shielded lead from Percussion Amp. Chassis
and short shielded lead from Power Amplifier Chassis.
3. Remove four screws securing Expres sion Control
Chassis to floor of cabinet.
4. Remove Expression Control as one.
5. Place new Expression Control in position and secure with
original screws.
6. Plug long shielded lead into Percussion Amplifier jack
and short lead into Power Amplifier Jack.
7. Using accompanying terminal strip, splice two Brown
wires from Expression Control into Blue & Gray 6.3VDC
filament leads originating in 6-pin rectangular plug
on Power Amplifier Chassis. Secure Terminal Strip to
cabinet floor with small wood screw.
8. Replace Expression Control Housing.
NOTE 3–12–A
If swell assembly is replaced as directed, circuitry will conform to
Figures 5-3 and 5-4.
3–13 TO REPLACE A BROKEN TAB
Proceed according to the following:
a. Remove four screws which secure metal cover on control
panel assembly.
b. Remove two Phillips screws from front of control panel which
hold bank of switches associated with tab to be replaced.
c. Remove lock washer from either end of switch assembly, and
pull rod out so it just clears broken tab. It may be necessary
to tilt assembly so that the free end of rod will clear adjacent
switch assembly.
d. Remove remains of broken tab and insert new piece.
NOTE 3–13–A
A small bronze spring washer will be found between tab and one side
of switch assembly. Be sure this is re-inserted with new tab.
3–14 PILOT LIGHT OR POWER SWITCH
Dis connect organ from power source, then proceed according to
the following:
Содержание L-100 Series
