Page 26
assembly to base. Control panel and drawbar assembly can
be folded over and rest on top of amplifiers.
k. Replace control panel mounting screws.
l. Prop up front of upper manual so that its terminal strip is
accessible. Be careful when raising and lowering manual that
its terminal strip is not damaged by rubbing lower manual
keys.
m. Unsolder manual cable from terminal strip. Lower manual into
normal Position.
n. Carefully lift manual assembly out of console.
3–8 LOWER MANUAL
To remove lower manual proceed according to the following.
a. Perform operations a. through e. of
.
b. Disconnect 9 colored wires emanating from right end of lower
manual which terminate at lower manual control tab switch.
c. Remove four screws from under manual assembly (front)
which secure terminal.
d. Remove lower manual end blocks by removing two screws
through manual frame and one screw through bracket on
cheek block.
e. Unsolder manual cable from terminal strip.
f. Tilt upper manual up from front. Remove two hexagonal bolts
that secure lower manual to case work.
g. Loosen four hexagonal head studs securing lower manual to
front rail. (Tighten these last when reinstalling manual.)
h. Lift out lower manual.
3–9 GENERATOR
To remove generator, disconnect organ from power source, then
proceed according to the following:
a. Remove generator power panel cover.
b. Unsolder all wires on power panel except yellow and grey
wires to motor and starting condenser.
c. Press generator-to-manual cable and generator-to-pedal
cable down and un-solder from terminal strip.
d. Unsolder grey wire which goes to pedal click filter and
remove heavy grounding wire (black).
e. Remove four hexagonal bolts which secure generator to
mounting angles. Lift out generator.
3–10 MOTOR
To remove motor disconnect organ from power source, then
proceed according to the following:
a. Remove generator power panel cover.
b. Unsolder grey wire to motor.
c. Unsolder red and black wires on starting capacitor.
d. Compress coupling spring between motor and generator and
remove spring.
e. Force off spring clamp which secures motor to mounting
frame. Lift out motor.
3–11 PEDAL KEYBOARD
To remove pedal keyboard, proceed according to the following:
a. Dress down generator-to-manual and generator-to-pedal
cables, unsoldering latter.
b. Remove two screws in lower back of console and three
screws between amplifier and front of console.
c. Lift console and pull out keyboard. (When reinstalling pedal
Содержание L-100 Series
