background image

System configuration

Domestic air conditioner

Operation

   Air Flow Direction Adjustment

Base  Operation

Remote controller

Emergency operation and test operation

Emergency Operation:

Use this operation only when the remote controller is defective 
or lost, and with function of emergency running, air conditoner
can run automatically for a while.
When the emergency operation switch is pressed, the " Pi "
sound is heard once, which means the start of this operation. 
When power switch is turning on for the first time and
emergency operation starts, the unit will run automatically in 
the following modes:

It is impossible to change the settings of temp. and fan speed,It 
is also not possible to operate in timer or dry mode.

Pi

1.

temperature is below 16

o

C, do not use it in the 

Test operation:

Use this switch in the test operation when the room

normal operation.

 your finger from the switch: the cooling

Continue to press the test operation 

switch for more than 5 seconds . After

 you hear the "Pi" sound twice, release

Test ope ration switch is the same as emergency switch.

operation starts with the air flow speed "Hi".

Under this operation mode,the fan motor of indoor

unit will run in high speed.

Pi Pi

    Room
temperature

Designated
temperature

Timer
mode

Fan

speed

Operation

mode

  Above 23

o

C

 26

o

C

AUTO

COOL

No

When restart after remote turning off, the remote controller 

When adjusting the flap by hand,turn off the unit.

When humidity is high,condensate water might occur 

It is advisable not to keep horizontal flap at downward
position for a long time in COOLor DRY

otherwise, condensate water might occur.

adjusted to left or at air outlet if all vertical louvers are right. 

mode ,

controller will automatically memorize the previous set swing position.

Note:

Pos.1

1.Status display of air flow

2.Left and right air flow adjustment

Pos.1

Pos.2

Pos.3

Pos.4

Pos.5

Pos.6

For each press of

button, remote controller 

displays as follows :

remote controller:

For each press of

button, remote controller 

displays as follows :

remote controller:

Cautions:

Initial state

Pos.2

No initial state disaplayed on remote controller, the
 vertical flap will be fixed on the current position

Remote controller:

Press

button

Every time the button is pressed, temp.setting
increase 1

o

C,if kept depressed, it will increase

rapidly

Every time the button is pressed, temp.setting

decrease 1

o

C,if kept depressed, it will 

decrease  rapidly

Select a desired temperature.

3.Fan function

2.Select temp.setting

Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.

 Unit start

 Press ON/OFF on the remote controller, unit starts.

/

changes as follows:

LOW

MED

HI

Display
circulated

For each press             button fan speed 

In HEAT mode,warm air will blow out after a short 
periodof the time due to cold-draft prevention function.

When FAN is set to AUTO, the air conditioner automatically
adjusts the fan speed according to room temperature. 

Cooling only unit do not have  displays and functions 
related with heating

Remote

Controller

Note

COOL

DRY

HEAT

FAN

In DRY mode, when room temperature becomes
lower than temp.2

o

C,unit will run intermittently

at LOW speed regardless of FAN setting.

Under the mode of auto operation, air conditioner will
automatically select Cool or Heat operation according
to room temperature.

air conditioner automatically adjusts the fan speed 

temperature.

When FAN is set to AUTO, the 

according to room

In FAN operation mode, the unit will not operate in
COOL or HEAT mode but only in FAN mode ,AUTO is
not available in FAN mode.And temp.setting is disabled.

In FAN mode,SLEEP operation is not available.

Operation

Mode

AUTO

Press             button to enter additional options, when 

cycle display to        ,       will flash. And then press

enter to FAN function.

Swing

Swing

Temp+

Temp-

Health

Extra Function

Confirm/Cancel

Timer On

Timer Off

Sleep

Lock

Light

Reset

Turbo/Quiet

Auto

Cool

Heat

Dry

1

3

2

2

4

Vertical flap

355

Содержание YR-HD
















































































































































Отзывы: