Super Match
6.Controller
YR-HD
Loading of the battery
1
2
3
4
Remote controller
Remove the battery cover;
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
Be sure that the loading
is in line with th
e" + "/"-";
Load the battery,then put on the cover again.
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
When electronic-sta rted type fluorescent lamp or change- over
type fluorescent lamp or wireless telephone is installed in the
room, the recei ver is apt to be disturbed in receiving the signals,
so the distance to the indoor unit should be shorter.
Note:
Full display or unclear display during operation indicates the
batteries have been used up.Please change batteries.
If the remote controller can't run normally during operation, please
remove the batteries and reload several minutes later.
l
p
s
i
d
e
d
o
M
..
1
l
p
s
i
d
g
n
i
d
n
e
s
l
a
n
g
i
S
..
2
4. FAN SPEED display
. LOCK displ
5.
6. TIMER OFF display
TIMER ON display
LO
MED
HI
7.
6. LOCK but
16.
Used to lock buttons and LCD display.
5. RESET but
25.
When the remote controller
appears abnormal, use a sharp
pointed article to press this button
to reset the remote
t
u
b
R
U
O
H
.
2.
2
2
Operation mode
AUTO
FAN
COOL DRY
Remote controller
HEAT
Hint:
Remove the batteries in case won't be in use for a long period. If
there is any display after taking-out, just press reset key.
1
2
3
4
5
9
10
11
12
13
14
15
16
17
22
23
24
25
19
20
21
8
18
7
6
Control the lightening and extinguishing
of the indoor LED display board.
3. SWING display
8.
..
9 QUIET but
t
u
b
T
A
E
H
.
0.
0
1
1. COOL but
11.
2. AUTO but
12.
t
u
b
N
A
F
.
3.
3
1
4. TIMER but
14.
t
u
b
H
T
L
A
E
H
.
5.
5
1
7. LIGHT but
17.
8. POWER ON/OFF but
18.
9. DRY but
19.
0. TEMP but
20.
t
u
b
G
N
I
W
S
.
1.
1
2
t
u
b
N
O
I
T
C
N
U
F
A
R
T
X
E
.
3.
3
2
CANCEL/CONFIRM button
24.
1
2
3
AUTO
Function: Auto, health airflow
upwards and downwards sending
function,sleep function,
air-refresh(reserved function)
Fahrenheit Celsius conversion
Power setting function
Function: Setting and cancel to the
timer and other additional functions.
Display
circulated
On the remote control do not have the functions of HEALTH.
Operation mode
Remote controller
QUITE
POWER
Supplemented
SLEEP electrical
heating
HEALTH
TEMP display
Additional functions display
Press FAN button. For each press, fan speed
changes as follows:
Remote controller:
Press
button
Every time the button is pressed, temp.setting
increase 1
o
C,if kept depressed, it will increase
rapidly
Every time the button is pressed, temp.setting
decrease 1
o
C,if kept depressed, it will
decrease rapidly
Select a desired temperature.
4.Fan speed selection
3.Select temp.setting
Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.
1. Unit start
Press ON/OFF on the remote controller, unit starts.
/
Base Operation
Remote controller
Operation
Mode
AUTO
Remote
Controller
Note
COOL
DRY
HEAT
FAN
Under the mode of auto operation, air conditioner
will automatically select Cool or Heat operation
according to room temperature When FAN is set
to AUTO the air conditioner automatically adjusts
the fan speed according to room temperature.
In DRY mode , when room temperature becomes
lower than temp.2
o
C, unit will run
intermittently at LOW speed regardless of FAN
setting.
In FAN operation mode , the unit will not operate in
COOL or HEAT mode but only in FAN mode ,
AUTO is not available in FAN mode. And temp.
setting is disabled. In FAN mode, sleep operation
is not available.
In HEAT mode, warm air will blow out after a short
period of the time due to cold-draft prevention function.
When FAN is set to AUTO, the air conditioner automatically
adjusts the fan speed according to room temperature.
1
4
3
3
LOW
MED
HI
AUTO
2. Select operation mode
2
COOL button:Cooling mode
HEAT button: Heating mode
DRY button: Dehumidify mode
Display
circulated
135