Haier YR-HD Скачать руководство пользователя страница 137

Страница: 137 / 143

System configuration

Domestic air conditioner

Operation

Timer On/Off On-Off Operation

TURBO Operation

(This function is unavailable on some models.)

Press HEALTH button , the remote controller will show
and then achieve to the health function.
Press again this HEALTH button , the

health function will be

cancelled.

HEALTH Operation

(This function is unavailable on some models.)

a lot of anion effectively balance the quantity of position

up the dust sediment in the room and finally clean the

and anion in the air and also to kill bacteria and speed

air in the room.

The anion generato

in the airconditioner can generate

1.After unit starts, select your desired operation mode.

2.Press

/ button to change TIMER mode.

Then select your desired TIMER mode (TIMER ON or

TIMER OFF ). " "or " "will flash.

3.Press

button to set time.

Hints:

After replacing batteries or a power failure happens, time

setting should be reset.

According to the Time setting sequence of TIMER ON or

Press the button for each time, setting time in the first

12 hours increased by 0.5 hour every time, after 12

hours,increased by 1 hour every time.

After adjust the time,press

button and confirm the

time ON or OFF button will not flash any more.

4.Confirm timer setting

5.Cancel timer setting

TIMER OFF, either Start-Stop or Stop-Start can be
achieved.

TIME
OFF

TIME
ON

TIME
OFF

TIME
ON

Loading of the battery

Remove the battery cover;

Load the batteries as illustrated.

2 R-03 batteries, resetting key

(cylinder);

Be sure that the loading

is in line with th

e" + "/"-";

Load the battery,then put on the cover again.

The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.

When electronic-started type fluorescent lamp or change- over

wireless telephone is installed in the

ver is apt to be disturbed in receiving the signals,

so the distance to the indoor unit should be shorter.

type fluorescent lamp or
room, the recei

Note:

Full display or unclear display during operation indicates the

ries have been used up. Please change batteries.

If the remote controller can't run normally during operation, please

reload several minutes later.

batte

remove the batteries and

Press button "

0.5 " will appear ,after 10 seconds

the time display will be blank.

TIME
ON

Press button "

0.5 " will appear ,after 10 seconds

the time display will be blank.

TIME
OFF

OFF

Press the button the time display eliminated.

Press the

cancel

（

TURBO

）

（

QUIET

）

When you need fast cool or fast dehumidification,you

can choose the Turob function; when you sleep, read,

you can choose Quiet function

bu on, you can switch the “Turbo”

and “Quiet”

will swith as below

When running in Turbo

，

the fan speed is the highest,

when running in Quiet, the fan speed is super slow

Turbo/Quiet

Auto

Cool

Heat

Dry

Turbo/Quiet

461

Содержание YR-HD
















































































































































Результаты поиска

Содержание YR-HD

Отзывы:

Похожие инструкции для YR-HD

Бренды по названию

Популярные бренды

Haier YR-HD, Руководство по обслуживанию

Результаты поиска

Содержание YR-HD

Отзывы:

Похожие инструкции для YR-HD

Бренды по названию

Популярные бренды