Haier GE DDT700S N0 Series Скачать руководство пользователя страница 75

Страница: 75 / 78

– 75 –

If the TCO is open, the thermistor must be

checked. If the thermistor checks good, then the

water level should be checked. A low water level

may cause overheating of stainless steel tubs.

The TCO is located on the right side of the tub,

approximately 16 inches from the front of the tub.

The TCO is in a series circuit with the Calrod

Heater.

No water or low water may cause the Tub TCO

to trip. Always check for proper water level if the

TCO is open.

The TCO is secured in place with a slide-in

mounting clip.

To remove the vent, the door must be removed

and separated (see the

Door

section of

Tub and

Structure

in this service guide).

The heater may be removed by one of two

methods. The first method requires door and

sump removal to gain access to the element nuts.

The second method requires the dishwasher be

removed from its installation.

Element Removal Without Uninstalling the

Dishwasher

1. Disconnect power to the dishwasher.

2. Remove the lower rack.

3. Remove the door (see

Door Removal

under

Door

in the

Tub and Structure

section of this

service guide).

4. Remove the sump assembly (see

Sump

Module Removal

under

Sump Module

the

Tub and Structure

section of this service

guide).

5. Disconnect the two wire leads to the heater.

6. Remove the two 15/16-in. heater nuts.

7. Remove the heater from inside the

dishwasher.

Element Removal by Uninstalling the

Dishwasher

1. Disconnect power to the dishwasher.

2. Remove the lower rack.

3. Remove the door (see

Door Removal

4. Remove the dishwasher from its installed

position and place on its back.

WARNING

: If the door is not removed and the

dishwasher is not placed on its back, there is a

TIP RISK.

5. Disconnect the two wire leads to the heater.

6. Remove the two 15/16-in. heater nuts.

7. Remove the heater from inside the

dishwasher.

Tub TCO Location

Heat Element Removal

Tub TCO

Venting/Airflow

Содержание GE DDT700S N0 Series















































































Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды

Haier GE DDT700S N0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды