Haier GE DDT700S N0 Series Скачать руководство пользователя страница 61

Страница: 61 / 78

– 61 –

The Diverter is the key component which allows

lower water use, by alternating water to the:

• Lower spray arm

• Silverware wash

• Mid/upper spray system (bottle wash)

• Mid spray arm and upper spray system) or

lower spray arm reverse (some models)

Operation

The rotation of the pressure diverter is counter-

clockwise as viewed from the top. The control

will seek the lower primary as the start of the

circulation cycle. Lower reverse and silverware

wash are only used during the main wash

segment of a cycle. A short spray will be

detected from the silverware wash, mid and

upper spray systems as well as the lower reverse

until the diverter is positioned to the lower primary

port.

Two Port Diverter Removal

The diverter top may be removed by removing

one 1/4-in. hex-head screw and pressing in on

the locking tab and turning counter clockwise

to remove. Removing the top will expose the

diverter check ball.

Pressure Diverter (Four Port)

Содержание GE DDT700S N0 Series















































































Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды

Haier GE DDT700S N0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды