Haier GE DDT700S N0 Series Скачать руководство пользователя

Страница: 43 / 78

– 43 –

Press firmly into place, using both hands to

push down on the sump module.

4. Latch the three sump latch cams. The latch

cams must not be used to pull the sump

module into place.

5. Connect the turbidity sensor and high drain

loop hose.

Stressing or softening the gasket ribs (pressing

the ribs against a hard surface, see below) will

make a new gasket seat easier. Lubricating with

a small amount of rinse agent or water will also

ease installation.

While inserting the sump assembly back into

the tub, use care to ensure the sump assembly

wiring and components are not pinched between

the sump and the tub.

NOTE

: Using rinse aid or water on the sump

gasket will aid sump installation.

Reconnect wiring to the pumps and flood

switch. Do not connect the turbidity sensor

until after the sump module is back in place

(step 5) to prevent damage to the connector.

2. Align the main conduit connection out of the

diverter on the sump module to the rear of the

tub and main conduit

Sump Gasket

Installing Sump Module

Содержание GE DDT700S N0 Series















































































Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды

Haier GE DDT700S N0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды