Haier GE DDT700S N0 Series Скачать руководство пользователя страница 47

Страница: 47 / 78

– 47 –

Entering

Service Mode

NOTE

: Entering Service Mode resets the CSM.

The dishwasher must be in Consumer Error Mode

to enter Service Mode. Entering Service Mode

will reset the CSM, allowing loads to be checked

for the cause of the CSM to trip. The control will

blink the Normal LED every few seconds for the

number of times corresponding to the load being

tested.

While in Consumer Error Mode

• Press and hold Cycle Select or furthest button

on left (some models) for 5 seconds.

• Press Cycle Select or furthest button on left

(some models) to select or increment each

test.

• Press Start, to start and stop each test.

Service Mode will exit after 5 minutes of inactivity.

Exit Service Mode by pressing and holding the

Cycle Select and Start pads for 5 seconds, or by

pressing any other pad.

LED

Blink

Load to

Control

Timeout / Notes

Drain

Pump

Attempts to empty.

Takes approximately 75

seconds from normal

level.

Water

Valve

Attempts to fill to

normal level. Takes

approximately 1 minute.

Circulation

Pump

Changes spray arm (via

changing diverter) every

30 seconds. Runs for

maximum of 2 minutes.

Heater

Turns on heater for a

maximum of 2 minutes.

Detergent

Module

Turns on detergent

module solenoid for a

maximum of 2 minutes.

Dry Fan

Turns the door fan ON/

OFF for models that

support this feature.

Heater

Relay Test

If the CSM trips, replace

the heating element

Diagnosing the main control and User Interface

(UI) control are covered in this section. Many

components can be checked from the main

control, which can be accessed with the door

on or removed if needed. Some connectors are

located through the bottom cover to allow easy

access to AC supply connector, door harness

and ACM or Appliance Control Module. The

Connect Plus Module (sold separately) allows the

appliance to communicate with the utility meter

when peak rates occur, and allows the appliance

to respond and operate in a manner that will

reduce energy usage of that appliance at high/

critical demand rates. For more information on

the module and display, refer to the separate

Connect Plus documents.

WARNING: GE Factory Service Technicians

are REQUIRED to follow Lockout / Tagout

(LOTO) 6 Step Process prior to beginning

repair.

Service Mode

Diagnosing Electronic Control Boards

Содержание GE DDT700S N0 Series















































































Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды

Haier GE DDT700S N0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды