Haier GE DDT700S N0 Series Скачать руководство пользователя

Страница: 67 / 78

– 67 –

The Main Conduit supplies water to the mid spray

arm, bottle wash and the upper spray system.

Main Conduit Removal

1. Remove both lower and upper racks.

2. Remove the lower spray arm.

3. Unclip the top of the conduit from the tub clip

at the tub top.

4. Remove the mid spray arm docking port by

releasing the tabs on each side of the docking

cone. The docking cone will remain attached

to the main conduit.

5. Pull the top of the conduit out of the

dishwasher to remove the bottom from the

diverter top.

Lower and Mid Spray Arms are twist lock design

and are the similar size and shape. The lower

spray arm has heat shields on the bottom and

is attached to the diverter. It is possible to

reverse the spray arms, which will result in poor

washability complaints. Care must be taken to

reassemble in the proper position. Some models

have an upper spray system which is also twist

lock.

Lower Spray Arm

The Lower Spray Arm provides an upward

directed water flow, which turns clockwise when

in operation. The arm, bearing, and nut come as

a complete assembly and has a twist lock design.

To remove, turn the nut counter-clockwise. Only

the lower spray arm has heat shields.

Middle Spray Arm

The Mid Spray Arm provides an upward directed

spray pattern to the upper rack. To remove the

mid spray arm, turn the nut clockwise (looking

down through the upper rack).

Main Conduit

Spray Arms

Содержание GE DDT700S N0 Series















































































Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды

Haier GE DDT700S N0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды