Haier GE DDT700S N0 Series Скачать руководство пользователя

Страница: 76 / 78

– 76 –

This design also uses the Exposed Heater and

adds a powered vent fan located in the door (see

the

Door

section under

Tub and Structure

in this

service guide for removal instructions).

Operation

Heater operation is the same as the passive

system. The fan is a brushless motor and

operated by 13.5 VDC and runs at 6,000 RPM.

There are no consistent resistance readings to

make a viable ohm check. A power dry cycle is

50 minutes, then the Clean light comes on. If the

consumer does not open the door, the fan will

run an extra 90 minutes before shutting off. If

the consumer opens the door, the fan will shut

off and not restart should the door be closed and

latched.

Diagnostics

The door will have to be removed and separated.

The door can be plugged back in and put into

Service Mode to make voltage checks. 12 to 14

VDC can be checked at the User Interface (UI)

board, connector J402 (2-pin connector) from

red

black

Vent Conduit

Insulation

Vent Grill

Vent Seal

Power Dry Fan

Vent Duct

Power Dry Forced Air

Содержание GE DDT700S N0 Series















































































Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды

Haier GE DDT700S N0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды