Haier GE DDT700S N0 Series Скачать руководство пользователя страница 45

Страница: 45 / 78

– 45 –

To Enter Consumer Error Mode

: With the

dishwasher in Standby Mode (not running a

cycle), press and hold the Cycle Select or furthest

button on left (some models) and Start buttons

simultaneously for 5 seconds.

On entry into the Consumer Error Mode, the

control reports the door status for 10 seconds.

• All LEDs are solidly illuminated, if the door is

detected as closed.

•

All LEDs are flashing, if the door is detected

as open.

• The SSD (Seven-Segment Display) will

indicate the User Interface (UI) software

version (without a decimal). For example,

software version 8.08 will display as 808.

After the door check, the control will enter a mode

to display any error codes that are currently

detected by the control.

Consumer Error Mode will time out after 5

minutes.

ANY KEY PRESSES OTHER THAN CYCLE

SELECT WILL EXIT THIS MODE.

LED

Error Type

Error Causes

Dry/

Dry

Boost

Wash

Temperature

Error

Minimum wash

temperature of 120°F

was not reached in

3 of the past 5 wash

cycles.

Temp/

Boost/

Temp

Wash

Thermistor

Error

Control detecting

short or open circuit at

thermistor.

Clean

Turbidity

Sensor Error

Control detecting

short or open circuit at

turbidity sensor. May

also occur on models

without turbidity sensor.

Lock

Always

Illuminated

Illuminates when Error

Code Display Mode is

active.

The Service LED has a continuous flash which

only advises the main control has power and the

control software is operating.

No display or LED’s will light.

Check for 120 VAC entering the main control. If

no volts are found, check the home breaker. If

main control has 120 VAC, check to see if the

service LED on the main control is flashing. If no,

replace the MC board. If there is a flash, check

the door harness and connections. Replace the

User Interface (UI).

If any of the mentioned LED’s illuminate, it

indicates the fault condition is present. These

fault displays cannot be cleared manually; they

will be automatically cleared by the control when

the fault condition is no longer present.

ANY KEY PRESSES OTHER THAN CYCLE

SELECT WILL EXIT THIS MODE.

Consumer Error Mode

Main Control Diagnostics

User Interface (UI) Diagnostics

To turn this option ON/OFF, press and hold the

Start and Boost pads for 5 seconds, close the

door and wait 3 minutes for the dishwasher

to go into sleep mode. In the OFF mode, the

control display, control sounds, and interior lights

(on some models) will not respond to the door

opening/closing. This mode can be used when

observing certain religious holidays such as the

Sabbath. To activate the control and interior

lights (on some models), press any pad.

Sabbath Mode/Door Wake Up Mode

Содержание GE DDT700S N0 Series















































































Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды

Haier GE DDT700S N0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды