Hagie UpFront DTS 8T Скачать руководство пользователя страница 56

Страница: 56 / 102

TRANSPORTING

1. Always have the booms in the folded position and cradled when driving or transporting. Adjusting

level cylinders, so the full weight of the boom rests in the cradle.

2. Flashing hazard/warning lights have been placed on the sprayer to warn other drivers.

3. A SMV (Slow Moving Vehicle) emblem has been mounted on the sprayer to warn other drivers that

one is moving slowly. Keep it properly displayed, unless prohibited by law.

4. Know and obey all state laws for driving farm equipment on a public road or highway.

5. Adjust the sprayer’s speed to suit the conditions.

6. Slow down and use turn signals before turning.

7. Pull over to side of road before stopping.

8. Keep a proper lookout, and maintain control of the sprayer.

9. Do not drive under trees, bridges, wires, or other obstructions unless there is clearance.

10. Use extra care before entering or leaving a public road or highway

11. Do not drive or highway machine on road when loaded.

A. DRIVING

When driving the sprayer on a public road or highway, drive carefully and follow these steps.

NOTE:

Be sure to read and understand the trailer’s owner and operator manual. Hitch the

trailer to the pulling vehicle as shown in the trailer’s owner and operator manual.

NOTE:

Extra care should be taken when loading the sprayer onto any trailer. Consider

whether it is best to back the sprayer on or drive the sprayer forward.

1. Loading:

B. TRAILERING:

Never load or unload a sprayer

with solution in the tanks.

Содержание UpFront DTS 8T







































































































Результаты поиска

Содержание UpFront DTS 8T

Отзывы:

Hagie UpFront DTS 8T, Руководство оператора, Страница: 56 / 102

Результаты поиска

Содержание UpFront DTS 8T

Отзывы: