hager TX216 Скачать руководство пользователя страница 12

Страница: 12 / 130

hager

Fitting, electrical connection and operation

Seite 12 von 130

Controls and indicators for manual control

ALL OFF

(8)

(1)
(2)
(3)

(4)

(5) (6)

(7)

ON/

OFF/

Fig. 4: Controls and indicators for manual control

(1)

key:

Activates / deactivates manual control

(2) LED :

LED ON indicates permanent manual control.

(3) ON/ key

Short press: Group ON / Long press: increases brightness of group.

(4) Status LED ON/ :

Indicates a group that is switched on (brightness: 1...100%) when LED ON in manual control

mode ).

(5) OFF/ key:

Short press: Group OFF / Long press: reduces brightness of group.

(6) Status LED OFF/ :

Indicates a group that is switched off (brightness: 0%) when LED ON in manual control mode.

(7) ALL OFF key:

All groups off (only in permanent manual control mode).

(8) 7-segment display::

Indicates the selected DALI group for the manual control

("01"..."32" /blinking = group disabled). In addition, the following information can be displayed

during a manual control...

": Manual control in unprogrammed state (broadcast mode). In this case, the DALI Gateway

collectively controls all DALI devices present in the system via a broadcast command as there

have been no group assignments yet (requires ETS commissioning).

": Indicates the automatic device replacement. The display duration depends on the number

of connected DALI devices. The display will extinguish, if the device replacement could be

completed without error.

": Indicates an error that occurred during the automatic device replacement. The device

replacement could not be carried out. The display will automatically extinguish after 3 seconds.

Содержание TX216



































































































































Результаты поиска

Содержание TX216

Отзывы:

hager TX216, Продуктовая документация, Страница: 12 / 130

Результаты поиска

Содержание TX216

Отзывы: