Hafco BM-23A Скачать руководство пользователя страница 11

Страница: 11 / 49

OPERATION MANUAL

2.1 SAFETY REQUIREMENTS

DO NOT use this machine unless you have read this manual or have been instructed in the use of

this machine in its safe use and operation

Safety glasses must be worn at

all times in work areas. Earmuffs

should be worn if the work area is

noisy.

Sturdy footwear must be worn at

all times in work areas.

Gloves should not be worn when

using this machine. Rings and

jewelery must not be worn.

Long and loose hair must be con-

tained with a net or under a hat

This manual provides safety instructions on the proper setup, operation, maintenance, and service

of this machine. Save this manual, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual may result in fire or serious

personal injury—including amputation, electrocution, or death.

The owner of this machine is solely responsible for its safe use. This responsibility includes, but is

not limited to proper installation in a safe environment, personnel training and authorization to

use, proper inspection and maintenance, manual availability and comprehension, application of

safety devices, integrity, and the use of personal protective equipment.

The manufacturer will not be held liable for injury or property damage from negligence, improper

training, machine modifications or misuse.

WARNING

DISCONNECT POWER FIRST.

Always disconnect

the machine from power supply before making

adjustments, or servicing the machine.

This prevents any risk of injury from unintended start-

up or contact with live electrical components.

OWNER’S MANUAL.

Read and understand this

owner’s manual before using the machine.

TRAINED OPERATORS ONLY.

Operators that

have not been trained have a higher risk of being

seriously injured. Only allow trained or supervised

people to use this machine. When the machine is not

being used, disconnect the power to the machine to

prevent unauthorized use—especially around chil-

dren. Make the workshop safe.

2. IMPORTANT INFORMATION

Page 11

Instructions Manual for BM-23A (M595D)

12/02/2018

Содержание BM-23A


















































Результаты поиска

Содержание BM-23A

Отзывы:

Похожие инструкции для BM-23A

Бренды по названию

Популярные бренды

Hafco BM-23A, Руководство по эксплуатации

Результаты поиска

Содержание BM-23A

Отзывы:

Похожие инструкции для BM-23A

Бренды по названию

Популярные бренды