Hafco BM-23A Скачать руководство пользователя страница 18

Страница: 18 / 49

OPERATION MANUAL

Do not use the quill power

feed at speeds above 2700 R.P.M. It is recommend-

ed to disengage the power feed worm gear when-

ever the power feed is not required. This avoids

unnecessary wear on the worm gear.

Do not move the Quill

Feed Lever unless the motor is at a complete stop.

When changing the lever position, do it gently.

The quill feed lever is located on the right side

of the mill head (Fig. 9). It is used to engage and

disengage the quill power feed mechanism.

The quill feed is engaged by pulling out the knob

and rotating the handle to a new locked posi-

tion. When engaged, the power feed mechanism

will drive the spindle upward or downward. The

power feed mechanism will not drive the spindle

when the handle is in the disengage position.

Feed Clutch Lever

The Feed clutch Lever (A, Fig. 11) is located on the

left side of the head behind the Manual Fine Feed

Handwheel (B, Fig. 11). It engages the overload

clutch on the pinion shaft when positioned to

the left. The Feed Clutch Lever stays engaged

until Quill Stop (C, Fig. 14) comes in contact with

Micrometer Adjusting Nut, forcing it to drop out

automatically, or until the operator releases it

manually by moving the lever to the right.

Fig. 9

Feed Rate Lever

The Feed Rate Lever (Fig. 10) is used to set the

quill feed per-revolution rate. Three feed rates are

available: 0.04mm,-0.08mm, and 0.15mm per rev-

olution. The positions are shown on an indicator

plate under the feed rate lever.

The rate is selected by pulling out the knob on

the feed rate lever and moving the handle to the

detent of the desired feed rate.

NOTE:

The knob is spring loaded – pull out to ro-

tate to new position. Unlike other controls on the

machine, the lever shifts into engagement more

easily with the motor running, and the quill feed

lever engaged

Quill Feed Lever

Fig. 10

Fig. 11

Feed Direction Control

The Feed Direction Control (B. Fig. 12) determines

whether the power feed will move up, down, or

not move at all. The position of the knob depends

upon the direction of spindle rotation (see the

Motor Switch section). The position of the control

may be changed with either the motor stopped

or running. If the control does not engage easily,

move the fine feed handle (A. Fig, 12) back and

forth to aid engagement.

If the spindle is rotating clockwise, the IN position

is downfeed; The OUT position is upfeed. When

the spindle is reversed the feed will also reverse.

The neutral position is between the IN and OUT

position

Page 18

Instructions Manual for BM-23A (M595D)

12/02/2018

Содержание BM-23A


















































Результаты поиска

Содержание BM-23A

Отзывы:

Похожие инструкции для BM-23A

Бренды по названию

Популярные бренды

Hafco BM-23A, Руководство по эксплуатации

Результаты поиска

Содержание BM-23A

Отзывы:

Похожие инструкции для BM-23A

Бренды по названию

Популярные бренды