Hafco BM-23A Скачать руководство пользователя страница 29

Страница: 29 / 49

OPERATION MANUAL

TROUBLESHOOTING

SPARE PARTS SECTION

The following section covers the spare parts diagrams and lists that were current at the time this man-

ual was originally printed. Due to continuous improvements of the machine, changes may be made at

any time without notification.

HOW TO ORDER SPARE PARTS

1. Have your machines model number, serial number & date of manufacture on hand, these can be

found on the specification plate mounted on the machine

2. A scanned copy of your parts list/diagram with required spare part/s identified

3. Go to

www.machineryhouse.com.au/contactus

and fill out the enquiry form attaching a copy of

scanned parts list.

Symptom

Possible Cause

Possible Solution

1. Poorly adjusted return spring.

2. Worn return spring.

1. Shorted/disconnected wiring.

1. Table locked.

2. Drive selector not engaged.

3. Sheared pin.

4. Gears not meshing or teeth missing.

5. Motor shaft and gear shaft not engaged

1. Rapid micro switch is stuck.

2. V.R. does not work properly.

3. Wiring harness unplugged from circuit

board

1. DRO is not turned on/plugged in.

2. Shorted/disconnected wiring/plugs..

1. Initial reading is incorrect.

2. Sensor has gone bad.

3. Spacing between sensor & scale is incorrect.

1. Power not turned on.

2. Bulb is burned out.

3. Short in wiring or wired incorrectly

1. Increase return spring tension.

2. Replace return spring

1. Inspect wiring connections. Replace/repair as

necessary.

1. Unlock table locks.

2. Select speed, engage drive selector.

3. Replace pin.

4. Check gears and adjust/replace.

5. Replace clutch.

1. Lightly tap on it to lower it.

2. Test/repair/replace

3. Reconnect wiring harness.

1. Press DRO ON/Power button/plug in.

2. Inspect circuit boards, sensors, plugs, and wiring

connections. Replace/repair as necessary.

1. Tare/zero/reset DRO at beginning point.

2. Test/replace sensor as necessary.

3. Adjust spacing between sensor and scale

1. Press switch/button on lamp or control panel.

2. Replace bulb.

3. Trace and test wiring. Fix any errors.

Spindle does not

fully retract.

Spindle switch does

not work.

Powerfeed does

not move table or is

slipping.

Operates at high

speed only or is

inconsistent.

DRO does not give

reading.

DRO reading is

incorrect.

Lamp will not light.

Power Feed

Digital Readout Unit (DRO)

Lamp

Page 29

Instructions Manual for BM-23A (M595D)

12/02/2018

Содержание BM-23A


















































Результаты поиска

Содержание BM-23A

Отзывы:

Похожие инструкции для BM-23A

Бренды по названию

Популярные бренды

Hafco BM-23A, Руководство по эксплуатации

Результаты поиска

Содержание BM-23A

Отзывы:

Похожие инструкции для BM-23A

Бренды по названию

Популярные бренды