background image

7

Attach the bar stop to the vise.

Insert the thread end of the long rod (R) into the side of the

vise.

Turn the long rod clockwise until snug.

Use a hex wrench 5mm to lock the screw M12x10 (Q) on the

sleeve counter-clockwise, so that bar stop unit is secure.

Assemble the coolant tank

Insert the coolant pump (X) into the coolant tank (T).

Apply an M6 washer to each of 2 M6x20 screws (U).

Secure pump (X) to tank (T) with prepared screws (U).

Place the hose clamp (V) onto the 0.375” flow tube (W).

Connect the flow tube (W) to the hose connector (V).

Use a flat head screwdriver to tighten the hose clamp (V).

Install the coolant tank

Orient the coolant pump (X) towards the rear opening of

machine stand.

Place the coolant tank (1A) onto the coolant platform (H).

The coolant tank (1A) contains a divider that forms a trough in

the bottom of the tank.  This trough fit over the vertical lip of

the coolant platform (H).

Insert one end of the 0.5” drain hose (Y) onto the hose

connector (1B) on the underside of the machine base.

Place the other end into the insert (Z) of the coolant tank (1A).

Attach the rear plate to the back of the stand.

Place rear plate (1C) across the back of the machine stand.

Align the plate holes (1D) with the set of 4 holes towards the

top of the machine stand.

Apply an M8 washer to each of 4 M8x25 screws.

Secure with 4 screws and washers.

Install the splash plates

Insert a splash plate (1E) onto the front sidewall of machine

base.

Align the 2 slots (1F) in the base of the splash plate with the

matching screw holes on the machine base.

Apply a washer for each of 2 hex socket head screws M8x20.

Loosely screw the socket hex head screws into the aligned

slot (1F) and holes.

Adjust the splash plate (1E) to the proper position and tighten

down the screws to secure.

Insert a longer one of splash plate (1G) onto the rear sidewall

of the machine base.  This plate need not be secured with

screws to allow free movement or convenient removal.

11

12

9

Q

R

10

X

U

V

W

T

1A

X

Z

Y

13

H

1B

1C

Y

1D

1D

1E

1F

1G

Содержание S829
































Отзывы: