manualshive.com logo in svg

H3C S3100V2-52TP, Руководство по настройке, Страница: 98 / 224

Поделиться
Скачать
H3C S3100V2-52TP Скачать руководство пользователя страница 98

 

86 

Figure 33

 

Layer 2 remote port mirroring implementation  

Source 

device

Intermediate 

device

Destination 

device

Eth1/0/1

Remote probe 

VLAN

Data monitoring 

device

Host

Remote probe 

VLAN

Eth1/0/2

Eth1/0/1

Eth1/0/2

Eth1/0/1

Eth1/0/2

Eth1/0/1

Mirroring process in the device

Eth1/0/2

Source port

Monitor port

Original packets

Common port

Mirrored packets

Egress port

 

 

On the network shown in 

Figure 33

,  

The source device does the following: 

1.

 

Copies the packets received on the source port Ethernet 1/0/1 to the egress port Ethernet 1/0/2.  

2.

 

Forwards the packets to the intermediate device, which then broadcasts the packets in the remote 
probe VLAN. 

3.

 

Transmits the packets to the destination device via the intermediate device.  

Then, the destination device does the following: 

4.

 

Receives the mirrored packets. 

5.

 

Compares their VLAN IDs to the ID of the remote probe VLAN configured in the remote destination 
group.  

6.

 

If the VLAN IDs of these mirrored packets match the remote probe VLAN ID, the device forwards 
them to the data monitoring device through the monitor port Ethernet 1/0/2.  

 

 

NOTE: 

•

 

Allow remote probe VLAN to pass through the intermediate devices to make sure the source device and
the destination device can communicate at Layer 2 in the remote probe VLAN. 

•

 

For a mirrored packet to successfully arrive at the remote destination device, make sure the VLAN ID of
the mirrored packet is not removed or changed. Otherwise, the Layer 2 remote port mirroring 
configuration will fail.  

•

 

To monitor both the received and sent packets of a port in a mirroring group, you must use the 

mac-address mac-learning disable

 command on the source, intermediate, and destination devices to

disable MAC address learning of the remote probe VLAN. For more information about the 

mac-address mac-learning disable

 command, see 

Layer 2—LAN Switch Command Reference. 

 

2.

 

Layer 3 remote port mirroring 

Layer 3 remote port mirroring is implemented through creating a local mirroring group on both the source 
device and the destination device, as shown in 

Figure 34

. 

Содержание S3100V2-52TP

































































































































































































































Отзывы:

Нет отзывов