GW Instek GDM-8251 Скачать руководство пользователя страница 47

Страница: 47 / 59

REMOTE

CONTROL

GDM

TxD

RxD

GND

Pin2

Pin3

Pin5

RxD

TxD

GND

Pin2

Pin3

Pin5

Configure GPIB interface

Configuration
step

GPIB terminal is a factory installed optional item. For a
new installation, contact the service center.

Press the Shift key, the 2ND

(Menu) key, the Right key
twice. The I/O configuration

menu appears.

Press the Down key, then the

Right key twice. The GPIB
selection display appears.

Press the Down key. The GPIB
address selection display

appears.

1st

display

Shows the current GPIB address 0~31

GDM-8200 Series User Manual

Move the cursor using the

Left/Right key. Change the
value using the Up/Down key.

GPIB address: 0 ~ 31

Press the ENTER key to

confirm GPIB and address
selection.

Connect the GPIB cable to the
rear panel terminal.

GPIB constraints

Keep these rules when using the GPIB interface.

•

Altogether less than 15 devices & 20m cable length,
2m between each device on the bus

•

Unique address assigned for each device

•

At least 2/3 of the GPIB devices turned On

•

No loop or parallel structure allowed

Functionality Check

Run this query command from the terminal.
*idn?
This should return the Manufacturer, Model number,
Firmware version.
GW, GDM-8200 series, V1.00

Содержание GDM-8251




























































Результаты поиска

Содержание GDM-8251

Отзывы:

Похожие инструкции для GDM-8251

Бренды по названию

Популярные бренды

GW Instek GDM-8251, Руководство пользователя

Результаты поиска

Содержание GDM-8251

Отзывы:

Похожие инструкции для GDM-8251

Бренды по названию

Популярные бренды