GW Instek GDM-8251 Скачать руководство пользователя страница 18

Страница: 18 / 59

BASIC

MEASUREMENT

Select beeper setting

Background

Beeper setting defines how GDM-8200 series notifies the
continuity test result to the user.

Pass

Beeps when the test result is pass

Beeper
parameter

Fail

Beeps when the test result is fail

Off

Beep function is turned Off

1. Activate
beeper setting
menu

Press the Shift key followed by

the 2nd (Menu) key. The system
menu appears.

Press the Down key followed by

the Right key. The beep menu
appears.

Press the Down key. The beep

setting appears.

2. Select the
beep setting

To change the setting, press the

Left/Right key.

Beeper

type:

Pass (beep when pass), Fail (beep when
fail, default), Off (beep off)

3. Go back to the
default display

Press the Enter key to confirm.
Press the Exit key to go back to the

default display.

GDM-8200 Series User Manual

Frequency/Period Measurement

To measure Frequency, press the
Hz/P key once.

1. Activate
frequency/period
measurement

To measure Period, press the Hz/P
key twice.

2. Frequency
(Period) mode
display appears

Hz (S)

Indicates Frequency (period) measurement

FREQ

(PERIOD)

2nd display shows the title

3. Connect the
test lead and
measure

Connect the test lead between the V
and the COM port. The display

updates the reading.

COM

10Hz ~ 800kHz

Frequency range

Sensitivity

10Hz ~ 100kHz: >0.1V

100kHz ~ 600kHz: >1.0V
600kHz ~ 800kHz: >2.5V

Period Range

1.25µs ~ 0.1s

Содержание GDM-8251




























































Результаты поиска

Содержание GDM-8251

Отзывы:

Похожие инструкции для GDM-8251

Бренды по названию

Популярные бренды

GW Instek GDM-8251, Руководство пользователя

Результаты поиска

Содержание GDM-8251

Отзывы:

Похожие инструкции для GDM-8251

Бренды по названию

Популярные бренды