Guilin Feiyu Technology FY3-ZT Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 31

Guilin Feiyu Technology FY3-ZT Скачать руководство пользователя страница 11

Guilin Feiyu Electronic Technology Co.,Ltd

Guilin Feiyu Electronic Technology Co.,Ltd http://www.feiyudz.cn Tel:0773-5815749

11

Way3.

Use two same frequency receivers, one installed on the ground adapter board, another one

on the plane. The precondition is the remote control can operate two receivers at the same time,
and the two receivers connecting channel must correspond with the autopilot and remote adapter.
Switch CH7 of the receiver which is installed on the autopilot can operate the autopilot just receive
one of the received signal.

Connection of the airborne part as follows:

GPS

Module

Data radio

AIL Servo

RUD Servo

THR Servo

ELE Servo

5V battery

Note: If the electric airplane use servo-powered
electric regulator, just plug the throttle control
port “THR” directly. And then you can power the
servo and the autopilot by the electric regulator,
but the electric regulator should have certain load
capacity. If you need to power the system and the
servo separately, you can power through the
unused port. Such as: plug the servo battery into
+5 V of the AD2 and GND port.

Diagram of the

Ground Part

RC Remote Receiver

AIL

THR

CH5

ELE

CH6

RUD

CH7

6

The receiver has to have at least seven
receiver channels; two of channels are
three-step switches. One of channels is
two-step switch .CH7 is used to switch
autopilot to work when its in the open RC
receiver mode.

«
...
9
10
11
12
13
...
»

Содержание FY3-ZT
































Отзывы:

Нет отзывов