background image

-

9

NS3000 Series User Manual    rev.01 

Chapter 2 Installation Guidance 

2.1 Introduction 

This

 

chapter introduces UPS installation, it provide normal installation steps and ideas. Please installation engineers 

operate according to    each place difference, 

  Warning-Installation can only be done by authorized engineers 

1. Do not apply electrical power to the UPS equipment before the approval of commissioning 

engineer. 

2. The UPS should be installed by a qualified engineer in accordance with the information contained 

in this chapter.

 

 

  Note: 3-Phase 4-Wire Input Power is required 

The standard UPS can be connected to TN, TT AC distribution system (IEC60364-3) of 3-phase 

5-wire.For    IT system please contact us.

 

 

  WARNING: battery hazards 

SPECIAL CARE SHOULD BE TAKEN WHEN WORKING WITH THE BATTERIES ASSOCIATED 

WITH THIS EQUIPMENT. When connecting the battery, the battery terminal voltage will exceed 

400Vdc and is potentially lethal. 

l

 

Eye protection should be worn to prevent injury from accidental electrical arcs. 

l

 

Remove rings, watches and all metal objects. 

l

 

Only use tools with insulated handles. 

l

 

Wear rubber gloves. 

l

 

If a battery leaks electrolyte, or is otherwise physically damaged, it must be replaced, stored in a 

container resistant to sulfuric acid and disposed of in accordance with local regulations. 

l

 

If electrolyte comes into contact with the skin, the affected area should be washed immediately 

with water.

 

 

 

 

2.2.1 Distribution Room 

The UPS is designed for indoor installation, which shall be located in a clean environment with adequate ventilation 

to  keep  the  environmental  temperature  within  the  required  specification.  The  UPS  uses  forced  convection  cooling  by 

internal  fans.  Cooling  air  enters  the  module  through  ventilation  grills  located  at  the  front  part  or  in  front  and  botton 

(NS3030)  of  the  cabinet  and  exhausted  through  grills  located  in  the  rear  part  of  the  cabinet.  Please  do  not  block  the 

ventilation holes. 

If necessary, a system of extractor fans should be installed to aid cooling-air flow. An air filter should be used when 

the UPS is to operate in a dirty environment and should be regularly cleaned to maintain airflow. 

Note: The UPS should be installed on a cement surface or other surface that is not combustible. 

 

-

10

NS3000 Series User Manual    rev.01 

2.2.2 Battery Room 

The battery will generate some amount of hydrogen and oxygen at the end of charging, so the fresh air volume of 

the  battery  installation  environment  must  meet  EN50272-2001  requirements.  The  ambient  temperature  of  the  battery 

must be stable. Ambient temperature is a major factor in determining the battery capacity and life. The nominal operating 

temperature  of  battery is  20°C.  Operating  above  this  temperature  will reduce  the  battery  life,  and  operation  below  this 

temperature  will reduce  the  battery capacity. If  the  average  operating  temperature of battery is increased  from  20

º

C  to 

30

º

C, then the service life of the battery will be reduced by 50%. If the operating temperature of the battery is above 40

º

C, 

then  the  battery  service  life  will  be  decreased  in  exponent  rate.  In  a  normal  installation,  the  battery  temperature  is 

maintained between 15°C and 25°C. Keep batteries away from heat sources or air outlets. 

If external batteries are to be used, a battery protection device (a DC circuit breaker) must be mounted as close as 

possible to the batteries, and the connecting cables should be as short as possible. 

2.2.3 Storing 

If  the  equipment  not  be  installed  immediately,  it  must  be  stored  in  a  room  so  as  to  protect  it  against  excessive 

humidity and heat sources. The battery needs to be stored in dry and cool place with good ventilation. The most suitable 

storage temperature is 20 

º

C to 25

º

C. 

2.3 Disassembly, Initial Checking and Positioning 

Check the packaging first upon the arrival of product to see if there is any damage; open the packaging to check the 

equipment; report any such damage to the shipper immediately. 

2.3.1 System Packing 

Remove  the  carton  box  and  the  plastic  film  first,  thensee.Durig  the  procedure  under  descript    Be  careful  not   

scratch the product. 

Содержание NS3000 10 kVA


























Отзывы: