Grundfos CIM 150 PROFIBUS DP Скачать руководство пользователя страница 15

English (GB)

15

7.3.1 Explanation to status module

AccessMode

Status bit indicating whether the booster system is controlled from 
the bus or from some other control source.

To allow the booster system to be controlled from PROFIBUS/
PROFINET, the RemoteAccessReq control bit in the 
ControlModule must be set to "1". However, certain commands 
from other control sources, for example Stop or Max. from a local 
source or external Stop from a digital input, have a higher priority 
and sets the AccessMode to "0", indicating that the actual control 
source is not PROFIBUS/PROFINET.

OnOff

Status bit indicating whether the booster system is started or 
stopped.

The booster system can be started and stopped from the bus by 
using the OnOff control bit in ControlModule. 
"Started" does not necessarily indicate that the booster system is 
pumping as it might be in a "low-flow stop" condition.

Fault

Status bit indicating that the booster system has been stopped 
due to an alarm.

Warning

Status bit indicating that the booster system has a warning.

AtMaxSpeed

Status bit indicating that the booster system is running at 
maximum performance.

AtMinSpeed

Status bit indicating that the booster system is running at 
minimum performance.

CopyToLocal

Status bit indicating that the booster will copy remote settings to 
local settings when it is switched from Access mode Remote to 
Access mode Local. The involved settings are the control mode, 
Operating mode and setpoint. This bit is not supported by Multi-E 
model G and earlier models.

ResetFaultAck

Acknowledge bit belonging to the ResetFault control bit. It will be 
set when the control bit is set and the command has been 
executed. It will be cleared when the control bit is cleared.

SetPointInfluence

Status bit indicating if the setpoint is influenced, for example by 
analog input. If influenced, the ActualSetpoint (module 29) will 
differ from the UserSetpoint (module 37).

Rotation

Status bit indicating that the booster system is pumping.

ProcessFeedback

In closed-loop control, this is the value of the controlled process 
variable (feedback/primary sensor). The process variable can 
always be compared directly with the ActualSetpoint variable. If 
no setpoint influence is active, it can also be compared with the 
setpoint variable in the ControlModule.
In open-loop control, setpoint is mapped to ProcessFeedback. 
The value of the feedback sensor can be read in the 
corresponding measurement module. 
See section 

7.8 Measurement modules

.

ControlMode

Status enumeration showing the actual booster system control 
mode. 
See section 

7.2.3 Explanation to control mode

 for detailed 

explanation to the various control modes.

OperatingMode

Status enumeration showing the actual booster system operating 
mode.
See section 

7.2.4 Explanation to operating mode

 for detailed 

explanation to the various operating modes.

0:

The booster system is controlled from a local source, 
display or Grundfos GO Remote, or from an external 
digital input.

1: The booster system is controlled from the bus, remotely.

0: The booster system is stopped (off).
1: The booster system is started (on).

0: No alarm.

1:

Alarm.
Booster system stopped, red booster LED on, FaultCode 
(module 4) shows the alarm code.

0: No warning.

1:

Warning.
WarningCode (module 3) shows the warning code.

0:

The booster system is not running at maximum 
performance.

1: The booster system is running at maximum performance.

0:

The booster system is not running at minimum 
performance.

1: The booster system is running at minimum performance.

0: Copy of remote settings to local settings is not active. 
1: Copy of remote settings to local settings is active.

0: No setpoint influence.
1: The setpoint is influenced.

0: No rotation (not pumping).
1: Rotation (pumping).

Pumpland.ru

Содержание CIM 150 PROFIBUS DP





































Отзывы: