2
THESE ARE IMPORTANT SAFETY INSTRUCTIONS. FOLLOW ALL INSTRUCTIONS AS INCORRECT
INSTALLATION CAN LEAD TO SEVERE INJURY OR DEATH
An electrician must disconnect electric power to the commercial
door opener before making repairs or removing covers.
Keep commercial door balanced
.
Sticking or binding doors must
be repaired. Commercial doors, door springs, pulleys, brackets
and their hardware are under extreme tension and can cause
serious personal injury.
Do not attempt to loosen, move or adjust
them.
Call for commercial door service.
Do not wear rings, watches or loose clothing
while installing or
servicing a commercial door opener.
To avoid serious personal injury from entanglement,
remove all
ropes connected to the commercial door
before installing the
door opener.
Installation and wiring must be in compliance with your local
building and electrical codes.
Connect the power supply cord only
to properly earthed mains.
Moisture and water can destroy the electronic components.
Make sure under all circumstances that water moisture or storage
moisture cannot penetrate the electronics. The same applies for
openings and cable entries.
Permanently fasten all supplied
labels
adjacent to the wall control
as a convenient reference and reminder of safe operating proce-
dures.
Disengage all existing commercial door locks
to avoid damage to
commercial door. Install the wall control (or any additional push
buttons)
in a location where the commercial door is visible dur-
ing operation . Do not allow children to operate push button(s)
or remote control(s).
Serious personal injury from a closing com-
mercial door may result from misuse of the opener.
Activate opener only when the door is in full view, free of ob-
structions and opener is properly adjusted. No one should enter
or leave the building while the door is in motion.
After the installation a final test of the full function of the sys-
tem and the full function of the safety devices must be done.
Make sure that people who install, maintain or operate the door
follow these instructions.
Keep these instructions in a safe place
so that you can refer to them quickly when you need to.
Safety Symbol and Signal Word review
This commercial door opener has been designed and tested to offer safe service provided it is installed, operated, maintained
and tested in strict accordance with the instructions and warnings contained in this manual.
WARNING
WARNING
CAUTION
Mechanical
Electrical
When you see this Signal Word on the following pages, it will alert you
to the possibility of damage to your commercial door and/or the com-
mercial door opener if you do not comply with the cautionary state-
ments that accompany it.
When you see these Safety Symbols and Signal Words on the following
pages, they will alert you to the possibility of serious injury or death if
you do not comply with the warnings that accompany them. The hazard
may come from something mechanical or from electric shock.
When operating a biased-off switch, make sure that other per-
sons are kept away.
The opener cannot be used with a driven part incorporating a
wicket door
(unless the opener cannot be operated with the
wicket door open).
The actuating member of a biased-off switch is to be located
within direct sight of the door
but away from moving parts.
Unless it is key operated
, it is to be installed at a minimum height
of 1500mm and
not accessible to the public
.
This appliance is not intended for use by persons (including chil-
dren) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance.
If the opener is installed at a height less than 2.5 metres from
floor level or any other level from which the unit can be ac-
cessed (eg mezzanine) the installer is responsible to fit guards to
the opener to prevent access to the chain drive.
Motor may become hot during operation. Appropriate clear-
ance and/or shielding should be supplied by the installer to
ensure any cabling, wiring and/or other items cannot come in
contact with the motor. If temperature rise exceeds 50⁰C all
fixed wiring insulation must be protected, for example, by
insulating sleeving having an appropriate temperature rating.
WARNING:
Important safety instructions. It is important for the
safety of persons to follow all instructions. SAVE these instructions.
Use the commercial door opener for its intended purpose.
eDrive +2.0 openers are designed for operating spring balanced
roller shutters, spring balanced roller doors and counterweighted
bi-fold and vertical lift doors.
