background image

14 

 

Door behaviour modes 

 

Latch up / Inch down mode (default): 

 

The door will travel upwards with only a single press and release of the UP button. The door will stop at the set limit. This mode 
is 

latch up

The door will only travel downwards when the DOWN button is held. The door will stop at the closed limit or when the button is 
released. This mode is 

inch down

 

Inch up / Inch down mode: 

The door will only travel whilst the UP or DOWN buttons are being held. The door will stop at the limits or when the button is 
released. To set this mode refer to 

Setting door behavior 

information below. 

 

Latch up and down mode:

 

Note:

 

This mode is only possible in conjunction with an Entrapment Protection Device such as an Infrared (IR) Beam or a 

Safety Bump Edge. Failure to do so may result in damage to property or injury to persons. 

Setting door behaviour 

 

To set the door behaviour modes, adjust the DIP switches in the corner of the MCB shown below.  
 
Dip switch 

1

 is used to latch 

DOWN 

and switch 

2

 is used to latch 

UP

 
At default the MCB is set to latch open and inch close, shown right. The door will open with a 
single press but  only travel downwards  while the down button is being held. For details on 
the 3 distinct modes refer above. 
 

* The door must only be set to latch DOWN if there is a suitable Entrapment Protection  
   Device installed. Failure to do so can lead to serious injury or death.

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
Note: **Both dips must be OFF (inch up/inch down) for Coles & BI-LO electrically operated roller door installations or when 
opener height is less than 2.5m from the ground without sufficient guarding of moving parts. 

 WARNING

 

Entrapment Protection 

The Entrapment Protection System for your installation will be determined by the functional requirements of the door. To ensure 
the installation meets these requirements refer to AS/NZS 60335-2-103. 
 
When using the Grifco® Protector System as part of the Entrapment Protection System, ensure it is installed to detect a 100mm 
high obstacle, ie; approx 80mm from the floor, and in accordance with installation directions supplied. 
 
Consideration should be given to the detection of vehicles or other similar equipment. To provide adequate Entrapment Protec-
tion an additional Grifco® Protector System may be required to be installed in a higher suitable position, for example, approx 
600mm from the ground. 

Latch up / inch down 

*Latch up / latch down 

**Inch up / inch down 

ON 

(LATCH) 

OFF 

(INCH) 

DOOR BEHAVIOUR AND ENTRAPMENT PROTECTION INPUTS 

Содержание eDrive +2.0

























Отзывы: