Gree GKH18D3FI страница 65 Скачать руководство пользователя

Страница: 65 / 191

U-Match Series DC Inverter Service Manual

maintenance etc., as shown in Figure 3-1-22.

Supply air

Return air

Supply air

Return air

Install the return air duct(a)

Install the return air duct(b)

Figure 3-1-22

Table 3-1-5 Installation of the return air duct

No.

Name

No.

Name

Return Air Inlet (with filter)

Indoor unit

Canvas Duct

Supply Air Duct

Return Air Duct

Grille

1.2 Installation of Floor Ceiling Type

1.2.1 Before Installation

After receiving the machine, please check for any transport damage. If finding any surface or internal

damage, please immediately report to the transport company or equipment company in writing.

After receiving the machine, please check the unit and accessories in reference to the packing list.

Ensure that the model is correct and the machine is in good condition. Please also check if the specification

and quantity of accessory parts are correct.

Determine the correct handling route and methods, thus to avoid damaging the unit or causing

possible hazard. For the sake of protection and safety, it is suggested to move the unit with the packaging

box. Even though it is not permitted to do like this under special occasions, do not remove the packaging

box, thus to avoid loosening or falling during handling.

Confirm if the installing foundation is solid. When this unit is to be installed on the metal section of the

building, make sure that the electrical insulation must comply with applicable standards.

Ensure that the place of installation is far from the area where the inflammable or explosive

substances are stored, thus to avoid possible explosion or fire due to leakage.

1.2.2 Installation Site

(1) Install the unit at a place where is strong enough to withstand the weight of the unit.

(2) The air inlet and outlet of the unit should never be clogged so that the airflow can reach every

corner of the room.

(3) Leave service space around the unit as required in Figure 3-1-23.

Содержание GKH18D3FI
































































































































































































Результаты поиска

Содержание GKH18D3FI

Отзывы:

Похожие инструкции для GKH18D3FI

Бренды по названию

Популярные бренды

Gree GKH18D3FI, Руководство по обслуживанию

Результаты поиска

Содержание GKH18D3FI

Отзывы:

Похожие инструкции для GKH18D3FI

Бренды по названию

Популярные бренды