Gree GKH18D3FI Скачать руководство пользователя страница 43

Страница: 43 / 191

U-Match Series DC Inverter Service Manual

Note:

You can purchase the accessory from Gree. The information is as below:

Name

Product code

Remark

Controller for door control function

(MK03)

MC207022

One controller for one unit

7.2.2 Human sensitive function

You can purchase the module of human sensitive function for this series. An interface for this module

is reserved on the main board of indoor unit.

(1) Interface instruction:

1) The printing is CN23 and the interface type is JST B3B-PH-K-S;

2) Electrical characteristic: 1-pin: +12V; 2-pin: detection port; 3-pin: GND; current: 150mA;

3) Working principle: when the module detects there is nobody in the room, 2-pin and 3-pin are

short-circuited and they are low electrical level; when there are somebody in the room, 2-pin

output is high electrical level.

(2) Function instructions:

In order to achieve this function, set it through wired controller and refer to the following operation

method. It is defaulted that this function is not activated; if this function is set and human sensitive module

is connected, the unit will control the ON/OFF of unit according to the signal detected by human sensitive

module. When there is nobody in the room and the unit is with wired controller,

icon will be displayed on

the wired controller; if the unit is without wired controller, there will be no display. The unit will control the

ON/OFF of unit according to the detected information.

(3) Setting method:

Under off state of the unit, press Function and Timer buttons at the same time for 5s to go to the

debugging menu. Press Mode button to adjust to “09” in temperature displaying zone. Timer zone displays

setting state and press ▲ or ▼ button to adjust. There are 2 selections:

1) Without human sensitive function (LCD displays 00)

2) With human sensitive function (LCD displays 01)

Choose the second selection and then press Enter/Cancel button to save and exit setting. Now,

human sensitive function is activated. The unit will memorize this setting status. The setting value will be

memorized after power failure. The detailed setting is as shown in the Figure below:

Содержание GKH18D3FI
































































































































































































Результаты поиска

Содержание GKH18D3FI

Отзывы:

Бренды по названию

Популярные бренды

Gree GKH18D3FI, Руководство по обслуживанию

Результаты поиска

Содержание GKH18D3FI

Отзывы:

Бренды по названию

Популярные бренды