Gree GKH18D3FI страница 56 Скачать руководство пользователя

Страница: 56 / 191

U-Match Series DC Inverter Service Manual

INSTALLATION

1 INDOOR UNIT INSTALLATION

1.1 Installation of Duct Type

1.1.1 Before Installation

After receiving the machine, please check for any transport damage. If finding any surface or internal

damage, please immediately report to the transport company or equipment company in writing.

After receiving the machine, please check the unit and accessories in reference to the packing list.

Ensure that the model is correct and the machine is in good condition. Please also check if the specification

and quantity of accessory parts are correct.

Determine the correct handling route and methods, thus to avoid damaging the unit or causing

possible hazard. For the sake of protection and safety, it is suggested to move the unit with the packaging

box. Even though it is not permitted to do like this under special occasions, do not remove the packaging

box, thus to avoid loosening or falling during handling.

Confirm if the installing foundation is solid. When this unit is to be installed on the metal section of the

building, make sure that the electrical insulation must comply with applicable standards.

Ensure that the place of installation is far from the area where the inflammable or explosive

substances are stored, thus to avoid possible explosion or fire due to leakage.

1.1.2 Installation Site

Ensure the top hanging piece has strong strength to withstand the weight of the unit.

The drainage pipe has convenient flow of water.

There is no obstacle blocking the return air inlet and exhaust outlet, so as to ensure sound air

circulation.

The installation spaces required by the drawing must be ensured, so as to provide enough space for

the service and maintenance.

The installation site must be far away from heat source, leakage of inflammable gas or smoke.

The indoor unit is of ceiling mount (indoor unit is hidden inside the ceiling).

The indoor and outdoor units, the power cable and the connecting electrical lines must be at least 1

meter from any TV set or radio. This is to avoid image interference or noise of the TV set or radio. (Even if

the distance is 1 meter, noise can also exist if there is strong electric wave.)

1.1.3 Caution for Installation

Generally, the unit is installed indoor on ceiling. For ceiling mounting, ensure that the hangers on

ceiling have adequate strength to support the weight of the unit.

To meet the noise and vibration requirements, the unit shall be installed by using rubber pad (thickness

≥20mm (13/16inch)) and rubber connector.

Insert a M10 expansion bolt into the hole. Drive a nail into the bolt. Refer to the profile dimensions

Содержание GKH18D3FI
































































































































































































Результаты поиска

Содержание GKH18D3FI

Отзывы:

Похожие инструкции для GKH18D3FI

Бренды по названию

Популярные бренды

Gree GKH18D3FI, Руководство по обслуживанию

Результаты поиска

Содержание GKH18D3FI

Отзывы:

Похожие инструкции для GKH18D3FI

Бренды по названию

Популярные бренды