Gree GKH18D3FI Скачать руководство пользователя страница 119

Страница: 119 / 191

U-Match Series DC Inverter Service Manual

116

2.4 IPM, PFC Testing Method

2.4.1 Method of Testing IPM Module

(1) Preparation before test: prepare a universal meter and turn to its diode option, and then remove

the wires U, V, W of the compressor after it is powered off for one minute.

(2) Testing Steps

Step 1: put the black probe on the place P and the red one on the wiring terminal U, V, W respectively

as shown in the following figure to measure the voltage between UP, VP and WP.

Step 2: put the red probe on the place N and the black one on the wiring terminal U, V, W respectively

as shown in the following figure to measure the voltage between NU, NV and NW.

(3) If the measured voltages between UP, VP, WP, NU, NV, NV are all among 0.3V-0.7V, then it

indicates the IPM module is normal; If any measured valve is 0, it indicates the IPM is damaged.

2.4.2 Method of Testing PFC Module Short Circuit (only for GUHD48ND3FO):

(1) Preparation before test: prepare a universal meter and turn to its diode option, and then remove

the wires L1-2, L2-1 after it is powered off for one minute.

(2) Testing Steps

Step 1: put the black probe on the place P and the red one on the wiring terminal L1-2,

L2-1respectively as shown in the following figure to measure the voltage between L1-2P and.L2-1 P.

Step 2: put the red probe on the place N and the black one on the wiring terminal L1-2,

L2-1respectively as shown in the following figure to measure the voltage between N L1-2 and NL2-1.

(3) If the measured voltages between L1-2P ,L2-1 P, N L1-2 , NL2-1 are all among 0.3V-0.7V, then it

indicates the PFC module is normal; If any measured valve is 0, it indicates the PFC is damaged.



GUHD18ND3FO/GUHD24ND3FO/ GUHD30ND3FO /GUHD36ND3FO/ GUHD42ND3FO

Содержание GKH18D3FI
































































































































































































Результаты поиска

Содержание GKH18D3FI

Отзывы:

Бренды по названию

Популярные бренды

Gree GKH18D3FI, Руководство по обслуживанию

Результаты поиска

Содержание GKH18D3FI

Отзывы:

Бренды по названию

Популярные бренды