Gree GKH18D3FI страница 132 Скачать руководство пользователя

Страница: 132 / 191

U-Match Series DC Inverter Service Manual

129

3. Remove the screws on

fan sub-assembly.

Remove the screws on fan sub-assembly.

4. Overturn the propeller

housing

Rotate the propeller housing to the air inlet

according to arrow direction.

5. Loosen the fan and

motor.

Use inner hexagonal spanner to loosen the

screws on fan and remove the clamp fixing

the motor.

6. Replace the motor

Firstly, disengage the motor from motor

support. Then, sequentially disengage the

fan sub-assembly form the motor shaft.

Remove the motor from the air inlet and

replace with new motor. In which, for the

motor with automatic motor support, the

motor support shall be removed in advance

and then changed to the unit.

7. Assemble the unit in

reverse to the

disassembly procedures

Assemble the unit in reverse to the

disassembly procedures and energize it for

testing.

Disassembly of filter screen for return air

Remark: Make sure that the power supply is cut off before disassembling and protect all the parts during disassembly. Do not

put filter screen near the high temperature heat source.

Step

Illustration

Handling Instruction

Disassembly of filter

screen for return air

Compress the filter screen for return air down

on the guide slot sponge, and remove

according to the direction shown by the

arrow. There are 2 filter screen for return air.

Содержание GKH18D3FI
































































































































































































Результаты поиска

Содержание GKH18D3FI

Отзывы:

Похожие инструкции для GKH18D3FI

Бренды по названию

Популярные бренды

Gree GKH18D3FI, Руководство по обслуживанию

Результаты поиска

Содержание GKH18D3FI

Отзывы:

Похожие инструкции для GKH18D3FI

Бренды по названию

Популярные бренды